Bass Shaker?

[SAY IT LOUD]

Hi All Shacksters today i brought 3 bass shakers to put in my 3 seat recliner. My question is how can i run them from my onkyo TX SR 705 when i am already running a sub where do i connect them too? any help much appreciated

cheers Troy

[hddummy]

You would use an RCA splitter and connect them to the same output that your sub is connected to. Happy rumbling!

[Mike P.]

You also bought an amp for the shakers, correct?

[SAY IT LOUD]

No i didn't. Cant i just do what hddummy suggested?

[Mike P.]

SAY IT LOUD wrote:

No i didn't. Cant i just do what hddummy suggested?

He assumed you had an amp for them. From the TX SR 705 one end of the splitter connects to your sub, the other end connects to an amp, the amp powers the shakers.

[SAY IT LOUD]

Thank you Mike P as you can see i need all the help i can get thank you

[Mike P.]

What brand and model did you get?

[SAY IT LOUD]

RESPONCE CS 2277 50w 4 Ohms variation force Peak 15Kg 20- 150Hz

[Mike P.]

I can't find "RESPONCE CS 2277". Do you have a link to them?

[SAY IT LOUD]

Yes i brought them from JAYCAR www.jaycar.com.au PS. What would be a good amp to run the and 2 sonosubs i want to build later?

[Mike P.]

Under what category are the shakers listed? Kind of a difficult site to find anything.

What subs will you be using? That will determine how much power you'll need.

[SAY IT LOUD]

I didnt search there web site for i was told by a freind then i called them and picked them up today. The subs are Riesen RCS300 12" single voice coil 4 Ohm 520W i am having the TSP measured tomorrow.

[Mike P.]

Post the specs when you get them and we'll see what they're capable of.

[SAY IT LOUD]

Ok cheers I cant believe how hard it is for us Aussies to get forming tube like SONOTUBE

[Mike P.]

Contact Sam at Affordable Drivers. He may be able to help.

http://www.affordabledrivers.com.au/

[SAY IT LOUD]

Im need a product like SONOTUBE here in OZ?

[Mike P.]

He is in OZ and has built a sonotube, he will know of a source.

[SAY IT LOUD]

ok thanks Mike.

[hddummy]

I did assume...my bad.

[SAY IT LOUD]

Hi Mike here are the TSP for my Riesen RCS300 12" single voice coil 4 Ohm 520W sub. FS 31.1 QT 0.87 QE 1.01 QM 5.94 VAS 106.86 litres MMS 82.6 grams DCR 3.82 ohms BL 7.8 L1K 1.08mh L10K 0.48 mh I need to know what size tube to use length & diameter look forward to your reply cheers Troy

[Mike P.]

We need to know the Xmax of the subs, whether it's 8 mm or 18 mm will determine what can be done with them.

[Blueeyedfrog]

Sonotube suppliers (called formatube or form tube here in Aus I think)


Genuine Sonotube (I have been informed): Bower & Lever or Hudson's hardware (Bower & Lever were cheaper though).

Bower & Lever
37 Victoria St
Windsor
Brisbane
Ph:3857-2018
(Hudson's Hardware dearer - quoted $355 for 762 x 3metre length)

Open:
6am-4.30pm weekdays
6.30am-11am Saturdays

About 13mm thick walls
Internal diameters:
610mm x 3 metre = $210.61
610mm x 6 metre = $285.51
762mm x 3metre = $314.92

Delivery = $44

These prices were valid about this time last year - probably dearer now

Hope that helps?

By the way - I have 4 jaycar bass shakers (2 x 2 units wired in series) and use and old NAD amp to power them (sacrilege I know). Works very well though and is especially popular with the neighbours.

Sam

[Blueeyedfrog]

As for amps for the sub - can't go past the Berhinger EP1500 or EP2500 for value for money - DJ-warehouse and/or New-Media are probably the cheapest suppliers in Aus at the moment.

[SAY IT LOUD]

Ok just got it XMAX is 6mm

[SAY IT LOUD]

Thanks Sam thats a big help cheers Troy