Speaker Cabinet Building Tutorial - Page 2 - Home Theater Forum and Systems - HomeTheaterShack.com

Thread Tools
post #11 of 26 Old 04-23-08, 08:25 AM
Posts: n/a
re: Speaker Cabinet Building Tutorial

Funkmonkey wrote: View Post
You can find C/A glue and "zip kicker" at any model shop, and most art supply stores.

Just to add on to this... Zip kicker is really just scented water. you can also use a spray mist of water if you don't have the kicker ( kicker is usually pretty $$ ). C/A cures when it comes in contact with moisture.

try it out... put down some c/a glue and mist it with water.. it will cure instantly.
Sponsored Links
post #12 of 26 Old 05-14-08, 10:58 PM
rodH, Rodney
Join Date: Mar 2008
Posts: 89
re: Speaker Cabinet Building Tutorial

Great thread guys.

I am getting ready to do a sub enclosure. I have a dewalt plunge router and am going to make a jig, seems easy enough.

I actually have a rotozip as well with an adjustable jig, but I am making it out of 1" industrial MDF and a couple test runs I did, the best way I found with the rotozip was to do it multiple depths, but even that gets slightly uneven (not a huge deal, but I am going to build another piece of decorative wood that is going to surround the 2 drivers, and need them to be PERFECT circles and the best/straightest finish possible. My buddy has a dewalt router I am barrowing for the project, it seems to feel more solid and should provide a better cut/hole.

My question is this, you mention to use a straight or upspiral bit. Which one do you prefer? I am planning on buying one, so I can get either one. The upspiral is about $5 more, but that is no big deal if it works better.

Also, if I am going to cut into 1" MDF and 1" plywood, do I have to have a 1" bit, or do I buy something shorter and just keep dropping it lower with the plunge router? If I am JUST using the bit for this project is the 1/4" bit the way to go?

rodH is offline  
post #13 of 26 Old 09-17-08, 09:34 AM
Join Date: Sep 2008
Location: Huntsville, al
Posts: 10
re: Speaker Cabinet Building Tutorial

very useful.
HSV HTGuy is offline  
post #14 of 26 Old 10-14-08, 05:34 AM
Join Date: Oct 2008
Location: Houston, TX
Posts: 31
re: Speaker Cabinet Building Tutorial

I use the Router Buddy circle jig. Unlike the Jasper jig, it is infinitely adjustable within its range.
johngalt47 is offline  
post #15 of 26 Old 10-14-08, 07:53 AM
Elite Shackster
HTS Moderator Emeritus
Anthony's Avatar
Join Date: Oct 2006
Location: Virginia
Posts: 2,216
re: Speaker Cabinet Building Tutorial

I think what people like about the Jasper jig is that for repetitive cuts, you can make a cheat list and repeat them exactly every time.

For example:
1/4" deep rebate (inset), 7 1/8" diameter
through hole, 6 1/2" diameter

You know those are your speaker dimensions, so you put the pin in the exact hole each time. Great for quick work, especially if you can't do the whole batch at one time.

That all being said, I have had drivers that needed to be just a tad less than one of the Jasper diameters (for insetting). So infinite adjustability would have been nice. In the future I now have the Bosch edge guide, which also has a circle cutting attachment.
Anthony is offline  
post #16 of 26 Old 07-02-10, 04:59 AM
Join Date: Jul 2010
Location: belgium
Posts: 11
Re: Speaker building tutorials

Mongrel714 wrote: View Post

Now, I am not an expert at this, far from it, information presented here
Is gathered from the web and from what experience I have found along the way, and if anyone has a better idea or an easier way, please include it here because this is to help anyone in the same shape as I, looking for information to help them along their journey through this wonderful hobby of DIY audio!

I suppose we will start with a tools list, this is what I used but once again, if anybody has suggestions…..
1. PLUNGE ROUTER. Probably the most important tool for this job, they come in many sizes and prices, my suggestion would be to find one with the smallest diameter body so you can cut some of the smaller mounting hole, with a bigger bodied router you are limited you may not be able to route out a hole for that 4" mid.

2. CIRCLE JIG. Runner up in the important tool list, you just cannot make perfect circles without some kind of jig, there are many commercial units available, Jasper being one of the best known, but making
your own is very simple and quite inexpensive; I will address this in my next tutorial.

3. ROUTER BITS. You will need two different bits for this project, first, a ¼” straight cut up spiral bit, which performs the main cuts and also helps to removes the MDF dust from the groove as it goes, (a regular straight bit will work also)
Second, a ¾” flat bottom bit to cut the recess groove for your drivers, these should be carbide tipped of course, my last non-carbide bit I tried was the ¼” straight cut bit, it lasted for two projects before it was to dull to use.

4. FLAP WHEELS. These little jewels are priceless when finishing the inside edges of your mounting holes.

5. DRILL. For pilot holes mounting holes, and Flap wheels.

6. PIVOT PIN. This is your pivot point for the circle jig, this can be a nail with the head cut off, or even a drill bit, I used a drill bit on my last baffles as the hole you drill for them is exact, so it works well.

The first step here is to determine your outside diameter of your driver for the recessed groove, and the through hole diameter, hopefully you can find this information from your retailer or manufacturer, if not, you can use two framing squares to find the diameter by turning your speaker face down, (protect your surround on the speaker) and laying the squares on the outside edges of the driver forming a square, measure the inside edges of the squares to find the diameter. Do the same for the through mounting hole.

Once you have determined your diameters, you must layout your driver placement on the baffles, then mark your centers for each driver, this is where the pivot pin is placed, the picture below shows the drill bit I used and the ¾” flat bottom router bit

Now measure the mounting flange thickness of your driver to determine the depth of your recess, if you want the driver surround recessed include this in your measurement, just don’t go so deep as to weaken the baffle you will be attaching to, for mids, I would keep it at least 3/8” thick.
Take your ¼” straight bit and make a shallow cut the diameter of your recess, then switch to the ¾” flat bottom bit and remove material in several passes down to your pre determined depth as shown in the above illustration.
Now, switch back to the ¼” straight bit, and in several passes, cut out the mounting through hole, many say to leave a small amount of material at the bottom of the groove and cut it with a razor knife afterwards, on small drivers I cut straight through myself as the circle jig will support the router when the plug falls free, use your own judgement on this one. Afterwards, use the flap wheel to finish out the inside of your hole, hopefully you will end up with something similer to this:

I hope you find this helpful! Happy building!!

I'm sorry I could not get the pics in the right place, I need to find a way to upload the word file or host it somewhere.
Verygood explanation & fine works!!!
horn-academy is offline  
post #17 of 26 Old 01-04-11, 10:58 PM
Join Date: Jan 2011
Posts: 7
re: Speaker Cabinet Building Tutorial

Very useful tutorial on making a speaker enclosure. Is there a tutorial on how to design a good speaker? I mean how large the speaker and the enclosure that goes with it.
mattphelps is offline  
post #18 of 26 Old 01-28-11, 02:07 AM
Senior Shackster
Join Date: Nov 2010
Location: Austin, TX
Posts: 315
re: Speaker Cabinet Building Tutorial

I just finished making a circle jig out of 1/2" MDF and cutting a bunch of circles in my internal braces. I'll post some pictures back here later.

One tip I have that I haven't read here is to use a sheet of junk plywood on some saw horses for your table. Drill a hole the size of your anchor pin in it. I use a nail with head still on the same diameter as the drill bit. Drill your center hole in your baffle. Insert the nail through your baffle and down into the table plywood hole. Now clamp your baffle to your table. Plunge the router halfway into the baffle. Don't plunge straight down - work your circle jig back and forth an inch or two as you plunge to keep the dust flying out. Lock the plunge depth and route the groove all the way around. Now flip your baffle over and reinsert the pin through the baffle and table hole. Plunge down and take out the 2cd half of the depth. This is for the through-hole of course. Do your driver counter-sink groove first.

Having the pin go through the table hole keeps the jig well anchored while the final cut is made.

I do my routing on the front driveway with a leaf blower in one arm while I push the circle jig around with my other hand. The leaf blower keeps the cut away dust out of the groove and keeps my router bit sharp. It also crop dusts my house and the surround two or three .
Wooderson is offline  
post #19 of 26 Old 05-26-11, 08:47 AM
Senior Shackster
Join Date: Aug 2010
Location: Minnesota
Posts: 350
re: Speaker Cabinet Building Tutorial

Cabinet making is just part of speaker building and for some its not a part at all. I think you should have called this "cabinet building tutorial."
Theresa is offline  
post #20 of 26 Old 05-09-12, 08:35 PM
Join Date: May 2012
Posts: 5
re: Speaker Cabinet Building Tutorial

I would rather buy my speakers, knowing me, id electrocute myself!
gsandhu25 is offline  


building , speaker , tutorial

Quick Reply

Register Now



Confirm Password
Email Address
Confirm Email Address
Random Question
Random Question #2

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address



Activation requires you reply to an email we will send you after you register... if you do not reply to this email, you will not be able to view certain areas of the forum or certain images... nor will you be able download software.


See our banned email list here: Banned Email List

We DO NOT respond to spamcop, boxtrapper and spamblocker emails... please add @hometheatershack DOT com to your whitelist prior to registering or you will get nowhere on your registration.

Email Address:


Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML is not allowed!
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


For the best viewing experience please update your browser to Google Chrome