Home Theater Forum and Systems - HomeTheaterShack.com - Reply to Topic

Thread: Toshiba TP55E81 RP STK392-110 Reply to Thread
Title:
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now




PLEASE COMPLETE ALL REQUIRED FIELDS BELOW... THANKS!

REQUIRED FIELDS ON THIS PAGE
YOU MUST COMPLETE ALL OF THESE

Username
Password
Confirm Password
Email Address
Confirm Email Address
Random Question
Random Question #2




User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
PLEASE READ BELOW PRIOR TO ENTERING AN EMAIL ADDRESS!

ATTENTION!

YOU MUST ACTIVATE YOUR ACCOUNT!

Activation requires you reply to an email we will send you after you register... if you do not reply to this email, you will not be able to view certain areas of the forum or certain images... nor will you be able download software.

AN INVALID EMAIL ADDRESS WILL CAUSE YOUR ACCOUNT TO BE DELETED!

See our banned email list here: Banned Email List

We DO NOT respond to spamcop, boxtrapper and spamblocker emails... please add @hometheatershack DOT com to your whitelist prior to registering or you will get nowhere on your registration.


Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
05-17-17 04:49 PM
frafreg
Re: Toshiba TP55E81 RP STK392-110

Any information or troubleshooting and schematic that can be provided would be much appreciated. Thank you.
05-17-17 04:47 PM
frafreg
Re: Toshiba TP55E81 RP STK392-110

I am able to remove and reseat the convergence board PB3366-1 while the set is off and get the picture back for a short period of time. The PB3366-1 plugs into the main convergence board which I believe is referred to as the PB3366-2.
05-17-17 04:43 PM
frafreg
Re: Toshiba TP55E81 RP STK392-110

With the exception of one 2.2 resistor, all other resistors were tested and in tolerance within 5%. The surrounding resistors were 2.2 ohm and 68 ohm 2 watt metal film.
05-17-17 04:40 PM
frafreg
Re: Toshiba TP55E81 RP STK392-110

Some additional information. The original STK392-110 chips failed the same way but lasted many years.
05-17-17 09:18 AM
frafreg
Toshiba TP55E81 RP STK392-110

Hi folks. I'm a new guy and just need some repair help with a rear projection set that lost the picture. I just replaced both STK392-110 chips on a Toshiba TP55E81 rear projection set that lost the picture. I ordered the chips for $21.95 from electronic-repair-kits because they say they only sell original Sanyo parts. I cleaned the old paste off the heat sinks and applied new paste to both chips. I also checked the resistors to make sure they were within 5% tolerance. I had to replace one 2.2 ohm resistor which was out of tolerance. I got the picture back and the set worked for about an hour. Then, I lost the picture again. I turned it off for a few minutes and turned it back on and the picture came back for a few minutes then I lost the picture again. Now, I can't get the picture to come back. While I did have a picture, I was able to adjust the red and blue convergence to get good center convergence. I was unable to adjust the outer edges where blue was out quite a bit. Is it possible I did not get original Sanyo parts? They looked like the ones I removed and felt about the same weight. Is there some way to tell the difference? Should I try another set of chips? Any help would be appreciated. Thank you in advance. Frank

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML is not allowed!

 


For the best viewing experience please update your browser to Google Chrome