Home Theater Forum and Systems - HomeTheaterShack.com - Reply to Topic

Thread: Steve and Aaron's 51PP9200D-37 Project Reply to Thread
Title:
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now




PLEASE COMPLETE ALL REQUIRED FIELDS BELOW... THANKS!

REQUIRED FIELDS ON THIS PAGE
YOU MUST COMPLETE ALL OF THESE

Username
Password
Confirm Password
Email Address
Confirm Email Address
Random Question
Random Question #2




User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
PLEASE READ BELOW PRIOR TO ENTERING AN EMAIL ADDRESS!

ATTENTION!

YOU MUST ACTIVATE YOUR ACCOUNT!

Activation requires you reply to an email we will send you after you register... if you do not reply to this email, you will not be able to view certain areas of the forum or certain images... nor will you be able download software.

AN INVALID EMAIL ADDRESS WILL CAUSE YOUR ACCOUNT TO BE DELETED!

See our banned email list here: Banned Email List

We DO NOT respond to spamcop, boxtrapper and spamblocker emails... please add @hometheatershack DOT com to your whitelist prior to registering or you will get nowhere on your registration.


Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
12-22-11 03:20 PM
SLR_65
Re: Steve and Aaron's 51PP9200D-37 Project

I dunno. I don't have a lot of time right now, probably won't till next week. I gave a link to the service manual in one of my earlier posts, download it and see how to read the codes and then look the codes up.

Sorry I can't help much for a bit, but it's just crazy around here right now!

Take care, good luck!

Steve
12-22-11 11:28 AM
Therjduncan
Re: Steve and Aaron's 51PP9200D-37 Project

I have this exact same tv that will not turn on and LED flashes 6 long and 1 short. Is what you did a similar repair? What exactly do I replace?
03-06-11 09:33 PM
SLR_65
Re: Steve and Aaron's 51PP9200D-37 Project

Hi Guys,

We reassembled this tonight and went to fire it up and . . . nothing! it was deader than a door nail!

I hadn't plugged it in before but my son had. He said it wouldn't come up but I just didn't think to ask if it blinked a code or anything. Not coming on is common with convergence issues so it didn't bother me. Usually they will at least give the power light and probably blink a code though so when he said it was always completely dead I figured I had another "fun" one to troubleshoot.

I always start with the basics though - check that the cord is good, check any fuses you see, etc.. Failing that it's time to hit the manual and see about any pico fuses, voltage test points, etc..

We pulled the back off and I went to remove the power cord to test it and what do I see? Someone had removed the power cord and when they reattached it they didn't get it on correctly - only one pin was making contact! I removed it and reattached it correctly and it came right up!

It's been a busy weekend and I was tired so I left at this point - my son called a bit after I got home, he got it converged and there was a firmware update for it on the Philips website that he installed - he said it had been running for quite a while now and seems to be just fine! It doesn't even appear to need the CRT fluid changed!

I think this set may end up in our family room . . . it's got a hdmi input, does 720p as well as 1080i and has a qam tuner in it! All fairly uncommon features in a crt rptv.

Here's a pic my son's girlfriend just emailed me.

Take care,

Steve
03-06-11 10:30 AM
SLR_65
Re: Steve and Aaron's 51PP9200D-37 Project

My solder is 60/40, but yeah - we tried adding some and then warming it up well before trying to suck it up but it just wasn't budging! It seemed we got a little more each time but it took several tries.

In the end we did exactly as you recommended - cut the leads and dealt with them one at a time.

Like I said though, this really surprised me as it was the most difficult de-soldering job I've ever encountered! Ever!

Oh well, it's just a bad memory now . . . we're past it and moving on - wish us luck!

Steve
03-06-11 09:26 AM
lcaillo
Re: Steve and Aaron's 51PP9200D-37 Project

When having trouble desoldering, add some 63/37 solder to the joints and make sure your iron is clean, not oxidized. Clean it often and add more fresh solder to lower the melting point. You can also just cut the chip out and do the pins individually.



03-06-11 09:02 AM
SLR_65
Re: Steve and Aaron's 51PP9200D-37 Project

Hi Guys,

We started on this last night but I was having camera problems so I didn't get many pics took so no step by step guide for this set, at least for now. I'm researching new cameras right now and if I run across another one of these I certainly will do a better write up.

For now a few comments that should help you along . . .

The manual is nice in that it's an electronic document and is searchable, etc. BUT evidently whoever wrote it never took one of these apart!

*) To start a convergence repair grab the manual and read the medium and small signal board removal procedures.

*) Though the manual says you can remove the medium signal board without removing the small signal board we removed it anyway as it's just in your way and it would be hard to see the wiring you need to unhook and to properly label it and stuff.

*) The small signal board removal procedure in 4.1.8 of the manual is a bit flawed. In addition to the screws they show that you need to remove to remove the cover there's also another one hidden. You need to skip down to step 5 and remove the ventillation grid from the side. There's a screw on the right side of that vent hole that also needs removed. (Grrr! This kinda stuff annoys me!) Don't miss the screw illustrated in Figure 4.8 that's on the far lower right - that screw is inside the case a couple inches instead of on the face of the plastic cover like the others.

*) Step 4 of the ssb removal instructions says to "Loosen all connections". Helpful, huh? There are 13 connections that need disconnected. Again, sorry I couldn't document them all for you since the camera was acting up but just label all the wires and the connectors they go to and you'll be fine.

*) Once the small signal board is removed you can start on the medium signal board. Many of the cables you unhooked from the small signal board lead to the medium signal board so you can leave the cables attached to the medium signal board. Make sure to confirm every cable is disconnected before you attempt to remove the board. We had 10 additional wiring bundles to unhook in addition to the 13 we'd already unhooked to remove the ssb for a total of 23 wiring bundles unhooked between the ssb and msb.

*) The medium signal board removal instructions in 4.1.7 are also a bit flawed. There should be a step in between steps 2 & 3 - there's a plastic piece that bridges across the board. I don't know exactly what it does other than provide a place to secure the wiring bundles to, but the feet of that bracket just barely covered part of the circuit board so it needed removed also before the board could be lifted out. It's secured by two screws on each side that screw down into the plastic circuit board support frame. The screws on the outside edge are next to the case so it's a tight fit to get your torx driver (all these are torx head screws) in the screw as the handle hits the case and pushes the bit at an angle instead of straight down. The one on the back side of the mounting foot was especially annoying -> it's not going back in!

*) Step 3 says to remove the fixation screws and shows where they are at - that's accurate, there are four right where they show them, but then it says "Pull the tab on the right hand side of the msb". Sigh, there are TWO tabs that need released to allow the board to be removed. Not a big deal, they are easy to see, but I sure wish someone would proof read these manuals before they are published!

Beyond those discrepancies the rest of the board removal instructions are ok and the pictures are actually pretty good.

*) Once the board is out you should check the twelve 6.8 ohm 1 watt flameproof convergence resistors. For 1 watt resistors they sure look tiny! They are installed in pairs in the circuit with one side to ground so you can test them in circuit, they'll just read 1/2 of their value so they should read 3.4 ohms. The pairs are 3149 & 3150, 3151 & 3152, 3153 & 3154, 3155 & 3156, 3157 & 3158 and 3159 & 3160. The resistors are on the back edge of the board right by the convergence amps, you can't miss them.

In our set 3155 & 3156 were visibly burnt and tested open.

*) De-soldering the chips was a real challenge though! Our Radio Shack desoldering iron just wasn't cutting it! I think they used some lead free solder or something as the solder just wouldn't melt and flow worth a hoot. We had to keep adding new solder, warming it up, then trying to suck it out. It seemed each time you made a little progress, but it took forever. This was the most difficult de-solder job I think I've done in my entire life! After fiddling with one chip for so long I was out of patience so I pulled up on the other chip to stretch the legs a bit and then just cut them with a small pair of diagonal cutters. Then I would put a rubber de-soldering bulb over the cut leg on top and heat the solder pad on the bottom and give it go - that through hole suction coupled with the soldering iron tip being inserted into the hole a bit (the desoldering iron doesn't have a protruding tip) seemed to do the trick, but it was still slow going! Again, I think they were using some new less toxic solder as I've NEVER had as much trouble as these connections were giving us!

That's it for now - when I left last night my son was soldering the new chips in. We're hoping to get it reassembled and test ran tonight unless something pops up (I'm working on picking up a 57" Sony so we may go grab it instead tonight), I'll keep ya posted as things progress and I did get a few pics took so I'll get them up soon too.

Take care,

Steve
02-24-11 04:44 PM
lcaillo
Re: Steve and Aaron's 51PP9200D-37 Project

You can use the -120 to replace the -110, but I tend to use them only in Philips sets that they come out of. I try to stick with what the manufacturer intended, or upgrade to the -150 from the -110, other than the Hitachi sets.



02-23-11 09:51 PM
SLR_65
Re: Steve and Aaron's 51PP9200D-37 Project

Aaaah, I see. And that answered a question in the back of my mind - I wondered why the 120 wasn't used as an upgrade for the 110.

Good to know, I'll stick your STK recommendation in the repair notebook too . . . that thing's getting thick!

As usual, thanks Leonard!

Steve
02-23-11 09:12 PM
lcaillo
Re: Steve and Aaron's 51PP9200D-37 Project

In the case of Hitachi, they did use the STK392-120 for a short time in some sets when they shifted from the STK392-110. They also supplied the -150 for a quite a while before the 394 series was available. In all Hitachi sets using the 392-110, 392-120, or 392-150, they shifted to the kits using the 394-160. The higher power rating on the -120 allowed it to be used as a sub for the others and you may see some sets that had them. In other sets like the philips products that used the -120, I would stick with that part. The set was designed with the higher current part. The hitachis were designed to use the -110 and direct replacements but sometimes came with -120s.

The bottom line is use what came out of the set unless you know otherwise. That knowledge is not so clear in some cases and may vary between brands, even within brands sometimes.



02-23-11 08:06 PM
SLR_65
Re: Steve and Aaron's 51PP9200D-37 Project

Hi Leonard,

The above is confusing me when contrasted with your chip comments in your main convergence repair post at:

http://www.hometheatershack.com/foru...e-repairs.html

There it says:

STK392-120 Hitachi replaces these with STK394-160, for other sets it may not be a good sub.

STK394-160 (This is my choice to replace the STK392-110, -120, & -150 in most Hitachi sets and are available in the kits in the next post)

If Hitachi is replacing the 120 with the 160 then it should at least match the 4 amp rating of the 120 one would think.

I agree though, one probably should stick to the original parts unless one is really sure it's a workable sub and the only subs I've seen for Philips sets with 120s are the sporadic 180 posts and I think those are in error as it sounds to me like the 180 is indeed a 3 amp device. I've seen many posts where the 160s were tried and didn't work and I've not seen even one where they did work, so they are off the table on this set.

It definitely looks like the 120 has no sub save for the 160 in Hitachis when recommended by Hitachi.

I ordered the 120s from Acme just a couple hours ago . . .

Take Care,

Steve
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML is not allowed!

 


For the best viewing experience please update your browser to Google Chrome