**Subs:** Dayton Audio DVC385-88 x2 **Receiver:** Denon 1913 AVR **Amp:** iNuke NU3000 non dsp I am a little confused on wiring my subs for the inuke. I assumed that I could simple connect my avr to the amp with one rca to xlr cable and then wire the subs to 2ohms and run the amp on mono...

As I have posted before. I own one Behringer 3000 DSP amplifier. I have been testing it and it sound pretty good so far. I have one 8ohm 1500 RMS dual speaker which I have connected in channel B. I have set the amp on stereo mode which feed the speaker with around 450 RMS. So i went and put it...

I am using input a on the inuke. I have a Rica to 3.5 to 1/4 adapter. Bought a speakon cable and cut one end off the run speaker wire to the sub. The sub has no output at all. If I unplug the 1/4" I get a pop. I think I have no out put from the receiver or something hooked up wrong. Help...

Hi, I know there are lots of inuke threads already but I was hoping someone could help me. I have an inuke powering a sunfire hrs12 subwoofer that had a faulty amp. Sunfire say the driver is 4 ohm and the amp was 1000rms. It has worked but never as well as the original amp. I have now...

I am almost finished my home theater!!! Finally!! I am looking to buy an amp to power 4 15" Dayton Ultimax in a sealed box. I am currently looking at 3 amps and wondering the follow: iNuke 3000 QSC PLX 3402 Crown XTi 4000 Is the QSC PLX3402 or Crown XTi 4000 amp a good amp for driving...

Im getting a new projector and need a 14.5' throw. These Epsons came up as my best option. Im not finding a lot of info on the 5020 around here. Visual Apex has the 5020 refurb for around $500 more than the 3000. The 5020 is clearly a better projector but is it worth the extra expense? I...

Hi, searched quite a bit but seems I can find solid info on how to wire these.. Given how many people seem to ask the same question one of you:) more experienced types should post a sticky.. I did a quick line diagram and this is my first attempt at pro gear so hopefully it works out. Could...

So I am about 99% dialed into a "MartyCube" build using a Dayton 460HO 18" driver with a iNuke 3000 DSP. The iNuke will be bridged and set to give a max of 1100 watts to the Dayton. Here is my question. I see some differing info on what the stock fan's voltage is on the iNuke. I plan to...

quick question. I haven't been able to find the answer in my googling.. I'm considering picking up the Peavey IPR 3000 to power a pair of 18 inch Stereo integrity's and have been waffling on amps. I found the IPR 3000 (not the IPR2 series) for $350 brand new... is the 840 watts into 4ohm specs...

Just a casual observance while I've been tuning using REW. The subwoofer is a sealed unit made by ADS, model SW5, that I fixed up to use while working on my own DIY Shiva X. When I hook up my Dayton SA240 (240W plate amp.) the little ADS comes alive with a great rumble with the gain knob...

I have a Yamaha RX-V673 av receiver, a direct tv receiver and a mitsubishi HC3000 projector, connected via HDMI. Everything was working fine until the other day when I began to get sound but no picture. The screen read "no signal." I connected the component video cables from the direct tv...

I obtained a copy of the URC MX 3000 Editor software through URC a few years ago. I was under the impression that it was the updatable version ( As outlined by the EULA that URC sent me and I signed ). When I first installed the software I was able to update it. Time has gone by and I want to...

Hey guys, Out of curiousity today I compared the frquency response of my Onkyo TX-NR1007, a INuke DSP 3000, and a Crown XLS-202. It appears the INuke DSP 3000 has a bit of a treble increase over the other two at the highest end of the audible spectrum, but nothing too outlandish. I used an...

Has anyone actually used this preamp in their system? Yes , I read the one or two reviews but I would also like comments from users . Thanks

Only $372.99 21% OFF | MSRP: $469.99 600 Available | 0 Sold as of 01/22/12 10:10am CST Free Shipping

Just bought this remote control my house...opened box and there is a rattle inside of it...was told this is normal...anyone have this ?..or heard anything about it?

S anyone out there currently using a URC MX 3000 (with mx 3000 editor) and windows 7 ????? I just spent my precious free time ( 2 kids: 3 yrs old and 18 months ) making a beautiful program. I went to download it to the remote and it fails about half way through. Says "connection failed". I...

ATI 3000 Series Amplifier Review ATI is the house brand of a Southern California amplifier manufacturer (the one that just bought Theta - hint, hint) that makes many other very high-end companies' power amplifiers for them. Led by Morris Kessler, a person whose has a passion, much like Dan...