Home Theater Forum and Systems banner

adjusting

  1. Home Theater Projectors
    I am mounting Optoma WU515ST to a ceiling and currently I am getting this shape. Please help me how do I adjust my projector so that the shape becomes square rectangle? Please see my attached image. The white grid lines is the current showing. I like it to be like the red rectangle
  2. REW Forum
    First time trying to run REW. Sorry if this is a dumb question but my time is limited and I have spent countless hours trying to figure this out with no luck. After calibrating my sound card I am having problems getting 75db without either adjusting the input gain on my focusrite 2i2 or using...
  3. System Setup and Connection
    Hello Forum Members. This is what I would like to do. Build a nice sounding 2+1 CH home stereo system for music listening. I already have L and R and a nice sub. I am going to replace my Pioneer SX-303R with a ONKYO 9050 integrated amp or ONKYO 9020 integrated amp. I like the 9050...
  4. Home Audio Acoustics
    Hello there! I am currently trying to adjust the acoustics in my home-studio (mainly for mixing) and need your help to sort out some issues! It's a 2,30m x 3,70m room (yes, it's metric, please continue reading) with carpet on the floor (about 2-3cm). Cieling is about 2,40m high. It also has a...
  5. Home Theater Receivers | Processors | Amps
    So I am fussy about vocals and front volume so I increase the fronts and center individually via the AVR - is this ok? Any repercussions? Will any equipment be "over" worked or put undue pressure on the Amp? Integra 30.4 AMP Def Tech Pro 1000 Def Tech Center 2000 SVS PB12 Def Tech 800's rear...
  6. Home Theater Design and Construction
    I was wondering what I should consider when deciding how high or low my screen should be adjusted to. I will have two row seating and with a riser. The ceiling is 8' and my first row seating is 11'. I have a motorized screen that I can adjust upwards or downwards. Thanks
  7. REW Forum
    HI I have a 2.2 (dual sub) setup. Im using JRiver Media Center 64 bit convolution feature with REW. JRiver seems only to take a single convolution file, but I would like to do corrections at the individual speaker level.. My question is: How do I do corrections on a per speaker basis and...
  8. REW Forum
    Hi. It's been a while since I last used REW. I calibrated the SC this morning and checked the levels which I set to 75dB, but when I run REW I get the clipping error message. Now am I better reducing my processor volume then re-calibrating REW's SPL meter to suit, or should I reduce the sound...
  9. Home Theater Receivers | Processors | Amps
    I bought a TX-NR3007 this fall. Love it. It was connected to my 7.1 system (Klipsch Reference and SVS PC12+ sub) from the start with no issues. Last week, I bought a used PC12+ to complete my 7.2 system. I connected the used unit to the Sub #2 pre-out on the AVR. I noticed that when I turn...
  10. Hitachi
    I have a Hitachi RP CRT that appears to have no convergence adjustment. A little history. When I got it two years ago it had bad convergence in one axis of one color. I replaced both IC's and all the resistors using the Hitachi kit. Worked great. A few months back it began losing convergence...
  11. Home Theater Receivers | Processors | Amps
    I picked up some X-amps off the classifieds and one of them has a much higher gain than the other three (like 10dB louder with the same signal). I opened them up to see if I could see anything that looked like a way to adjust it but nothing jumped out at me. Any ideas? Also all of them - with...
  12. Blu-ray | DVD | Disc Media Players
    I just bought a Samsung bd-6500 and I can’t adjust any thing on my tv… color contrast refresh any thing when I plug it in to the tv… I have a Samsung 8 series. Bought the blu ray at best buy so I can take it back no problem
  13. Electronic Processing/Equalization Devices
    Hi there, I am curious to find out if there is a way of adjusting the input levels (gain) on a BFD like the gain on an amplifier. When I connect my BFD in the chain my levels overall drop quite a bit and I have to increase my sub trim level up to get back to 80db for my sub (my preference). I...
  14. Panasonic / Technics
    Panasonic PT-65WX50 Convergence Adjustment 1999 Panasonic PT-65WX50 HDTV I'm trying to correct the convergence as it has shifted slightly and can't be corrected with the simple single point adjustment in the main menu. I have found the service mode, but I am not sure how to adjust the...
  15. Home Theater Seating and Accessories
    I purchased a couple sets of Berkline theater seats used. I'm not sure if they are the 13217 or the 13084, they kinda look the same in the pictures I've seen. The previous owner said he bought them at Costco. My plan is to put them into our theater room with two rows of three seats with the...
  16. System Setup and Connection
    I wanted to see if I could get some response from Home Theater Shack forum readers about considering the passive crossover phase characteristics of main speakers(FL,C,FR,RR,LR) when calculating and making subwoofer phase adjustments since most powered subwoofers will use active crossovers and...
  17. Home Audio Acoustics
    Hi This is my first post, hope I'm in the right place. I have just started with REW and have a recording area that I want to get the best RT60 results by adjusting the suspended ceiling. I have a 60cm grid for ceiling tiles with slight inclination. I have 1cm or 2cm rockwool tiles and...
  18. System Setup and Connection
    Hello All, I've joined because I really need to build up my education on this stuff. I know I like good sounds and great Movies at home. here is alist of how I am currently set up with some changes on the way. Hk AVr 745 Fronts - Klipsch 3.5s Center - klipsch RC52 Rears - Speakercraft 8in...
  19. AV Home Theater
    Does anyone know where to obtain a video file of audio test patterns that help you adjust audio sync? I remember reading about how HD television services have audio sync test patterns that run late at night, but I don't subscribe to anything right now. It would be appreciated if someone could...
  20. REW Forum
    This is what I did and it works :jump::jump:. Before testing and adjusting any acoustic compensator attached to your amplifier , first take your speakers outside place them the same distances that they will be in the HT and place the calibrated mike at the same distance that you will be sitting...
Top