Home Theater Forum and Systems banner
amp
481-500 of 500 Results
Advanced
  1. Home Theater Receivers | Processors | Amps
    Right now i have a Yamaha RX-V1700 receiver rated at 130 watts per channel. I am powering Onix X-LS speakers for fronts and an Onix X-CS for center. My rear surrounds are HTD level 3's. Now i was wandering into the power amp route. Now i need suggestions. Shouls i get a monoblock amp to power...
  2. Subwoofer Amps | High Pass Filters
    Hi folks, I would like to know if anyone has used QSC 1602 or RMX850 to drive your IB drivers? I can find these 2 locally and was hoping if it would be better than the one I'm purchasing online, the EP2500. I would be driving two Fi Q18"s IB modified drivers. The manifold is done and wife has...
  3. DIY Subwoofers - General Discussion
    I am currently just about to start construction on a new subwoofer and I am using two 3 inch ports. My question is should they be the same length or what happens if i tune them to slighly different frequencies? ex. 25 and 30 hz
  4. DIY Subwoofers - General Discussion
    I have one 12" Peerless XLS driver, two 12" Peerless XLS passive radiators and one 350watt amp module. Driver specs: Nominal impedance 8ohm Zmin ohm/Hz = 4.7/106 Maximum impedance ohm 64.2 Resonance frequency fs 18.1Hz Mechanical Q factor 3.70Qms Electrical Q factor 0.21Qes Total Q factor...
  5. DIY Subwoofers - General Discussion
    Hello Everyone, I have been doing research on the Internet in building a WAF subwoofer to be as stealth as possible in order to match my Artison Portrait speakers alongside my 50 inch plasma. By luck I found this forum and am impressed by the knowledge of subs and designs I see so I would like...
  6. Home Theater Receivers | Processors | Amps
    I just need a little amp to drive my secondary center speaker. Really all it needs is maybe 50 watts and a gain control, but it would be really cool if I could cut the low freqs a bit, as it sort of struggles and can't keep up with the main center. If it helps any, the center I want to drive is...
  7. AV Home Theater
    I bought a 19" Phillips 19pfl5622d television for my office and I want to improve audio amplification. Problem is there are only 2 audio outputs on the tv = s/pdif and headphone jack. I will be buying a Dayton APA150, 2 channel amp to use with my REW test set up. I want to use the new amp with...
  8. REW Forum
    As much as it hurts - I've been thinking again... I would like to test each speaker in my system, and Im a bit concerned I might damage my AV receiver, swapping wiring around. I believe I can use a single channel amp to power each speaker individually - can't I ? Thanks... Hermit... peace and...
  9. Two Channel Audio
    I was comtemplating getting one of these two amps for a desktop system. Any preferences between the two anybody? They seem pretty similar in intent. Just wondering if anybody has any experience with either.
  10. Computers | HTPC | Media Servers
    Any suggestions for a good integrated amp that I can use to power a small set of bookshelf speakers? (Epos ELS3) Will be used to replace my computer speakers I'd like something with a volume control, take as little desk space as possible and good sounding but not expensive. Multiple inputs is a...
  11. Subwoofer Amps | High Pass Filters
    Hi there! any body know what plate amp would be best to drive aJL 13w7. need help urgently. thanx chaps.
  12. Subwoofer Amps | High Pass Filters
    So I am thinking about building another sub exactly like my other sub. I am getting the Driver an ED 13Kv.2 and it would be no problem to get the enclosure done. Problem is the first one is powered by a BASH 300S which is out of stock. I could wait to see when it comes back and when it goes on...
  13. Home Theater Receivers | Processors | Amps
    My wife thinks I need to give her some Christmas shopping help. So I'm thinking: 1- B&K 200.7 S2.......~$2400 375w at 4 ohms 76 lbs 2- Outlaw 7700 7..... ~$2150 300w at 4 ohms 93 lbs 3- Emotiva MPS-2 7...~$1700 300w at 4 ohms 115 lbs 4- Save the cash to finish basement (including the HT)...
  14. Two Channel Audio
    Hi right now i have a 5.1 setup using a Yamaha RV-X1700 receiver. I want a good 2 channel amp to power my Rocket 850 signatures. And i don't want a cheap amp, but i also don't want to break the bank. Basically i want a dedicated 2 channel amp to get the most out of my 850's. Any suggestions?
  15. Classifieds - Speakers and Subwoofers
    Seeking either one or two plate amps capable of driving two pyle 15" 1000 watt subs pretty hard (each is 4 ohm) in a box no larger than 10fc (box size can be cut down accordingly). Budget for amp is no more than $175 for used.
  16. Subwoofer Amps | High Pass Filters
    Has anyone used a regular plate amp for a pro-sound subwoofer? If so, how well did it work? I'm thinking of doing this and can't think of a reason why it shouldn't work.
  17. Home Theater Receivers | Processors | Amps
    Trying to find out if there is a general rule of thumb in determining if someone like me would benefit by adding an amp.I've only had 1 experience with an amp a sunfire (300x2) i felt my receiver alone sounded better.I dont know if all amps have their own sound but this one did.I for one would...
  18. Subwoofer Amps | High Pass Filters
    So I have a small project with an EHQS 8 and a 70 W Dayton Plate Amp with a 4" Dia. port at 13" long to give a tuning of 25 Hz in a 12" Dia x 36 " Long tubing. Problem is I would like to mount the amp in the tubing and I have been fiddling with ideas on how to do this. Any one ever did anything...
  19. Subwoofer Amps | High Pass Filters
    Hello all, I have a question for the Forum Gods.. I have a Polk PSW1000 sub without a amp...I need to know if anyone has direct experience with either the O audio 500 W bash or the Parts Express HPSA 5oo. They are both about the same $$ and wattage. I'm limited to size a bit as the opening for...
  20. Home Theater Receivers | Processors | Amps
    Due to illness in the family my last amp project had to get put on hold (mainly becasue it was a very time intensive project). However recently I have found enought time to do a smaller easier project. A gainclone with 20Watts per channel. The basis for the amp is the 20watt amp kit from...
481-500 of 500 Results
Top