Home Theater Forum and Systems banner
asio
1-20 of 43 Results
  1. REW Forum
    If this issue has been raised before, I couldn't find it. Please point me in the right direction if it has. My bottom-line question: "Is it possible to use REW in ASIO/HDMI mode with a preamp/mic instead of a USB mic? I'm now able to send test signals to each speaker without switching cables...
  2. REW Forum
    If I use JAVA the UMIK1 USB is in the input list. If I select ASIO the UMIK1 USB mic is not in the input list. I installed ASIOALL and the UMIK1 USB is in the input list but a much lower input level than java. Should I use the JAVA driver or ASIOALL driver ? Thanks, Andy P.S.: There...
  3. REW Forum
    Installed 5.19b2 and now the driver drop down is empty on startup. I have to switch to Java and back to asio to get it to populate.
  4. REW Forum
    REW 5.17 beta 12 doesn't recognize ASIO driver Hi there, Used REW 5.17 beta 7 previously with my M-Audio Revolution 7.1 sound card in ASIO mode and it worked fine. I'm trying to use 5.17 beta 12 [current at this date] on Windows 10 with the last-available 64-bit drivers for the Revo7.1 which...
  5. REW Forum
    Hi please can someone tell me the benefits of using ASIO, other than it is easier to measure multiple channels Thank you
  6. REW Forum
    I'm running a Native Instruments Kontrol S4 MK2 as my soundcard. The S4 has two stereo INs, stereo mic IN, and 2 stereo OUTs. When I try to calibrate the soundcard with the loopback, the driver crashes immediately. After a fresh launch of REW, I can start the soundcard calibration and see the...
  7. REW Forum
    Everything was going fine, I was going through Jerry's guide step by step. But then ASIO would not recognize both at the same time, my Umik mic and my Denon 1911 receiver. At one time, it showed the AVR and all 8 channels. And at another time it showed my Umik mic. But I just can't, for some...
  8. Electronic Processing/Equalization Devices
    Hey guys, its my first post, so please be kind :-) I have a question, but first Ill give a short overview of the starting point. Like almost anybody i have two speakers in a room, and want to listen to music from my computer. I set up the stereo triangle on the best (measured) position...
  9. REW Forum
    Hello, I did some measurements in Java but I'm trying to ASIO because I am full HDMI and can thus choose the output I want. But I do not have the same curve in JAVA and ASIO ? The curve changes on many frequency and level is not the same...
  10. REW Forum
    I had everything working fine on Windows 10. I've just recently re-installed windows. Now I get "The sound card did not provide any input data" when I try and activate my UMIK. I can play test tones through HDMI just fine, but obviously without the microphone working it's not very useful. Using...
  11. REW Forum
    Hi is it possible good practice to use ASIO drivers with XTZ Room Analyser pro mic?
  12. REW Forum
    Can someone tell me how to use REW with different ASIO devices? If I select in Preferences--> Drivers--> ASIO, i can only select one ASIO Device. I want to give the sweepsound to Output: ASIO-->Asio Decice:JRIVER Media Center21--> I want to read the microphonesignal from Input: ASIO-->ASIO...
  13. REW Forum
    Hello, I'm using REW 5.13 under Windows XP SP-3 and I'd like to use My Audio GD DAC as output together with my Digidesign Mbox 1 with phantom power connected to my MIC for Input. Both peripherals have ASIO drivers and I can setup and make them working fine separatly but setup using both...
  14. REW Forum
    Hello, When I use the Java driver, REW clearly sees the incoming signal from my microphone and I can make measurements. But as soon as I switch to ASIO, then there is no signal. On a choice there are only two "incoming devices: HD1 and HD2.While in device Manager, the microphone works, it not...
  15. REW Forum
    Here's the scenario. I use REW at work sometimes to measure impedance of different drivers. (I am a custom car audio installer by trade). The best audio interface (for my application) I have found so far is the Focusrite Saffire6 USB. Super flat freq. response, no calibration necessary...
  16. REW Forum
    I have found a possible bug with REW 5.1 or ASIO4All maybe you can help with. If using the EMU ASIO I am able to loop back SPDIF from input to output, using external clock and matching sample rates ie 96 kHz, works good. But if I use ASIO4ALL (which I need to do to output on HDMI and input on...
  17. REW Forum
    Hello I just got myself a UMIK-1 but i cannot get it to work with ASIO on my mac with windows bootcamp I am following this guide: http://www.minidsp.com/applications/acoustic-measurements/umik-1-hdmi-on-windows All works untill i get to the ASIO4ALL control panel section When i first...
  18. SPL Meters | Mic's | Calibration | Sound Cards
    I have built an active theater system using JRiver (v20). My sound card is an SSL MX 4:16 linked to a MaxiXtrem64 PCI-card. The system contains no physical filters, Jriver filters digitally and outputs sound to 13 separate amplifier channels (5 x tweeter, 5 x midrange, 2 x mid bass, 1 x sub)...
  19. SPL Meters | Mic's | Calibration | Sound Cards
    I'm trying to set up REW with a UMIK mic. I Downloaded the ASIO4 control panel. My problem is when I try to set up the preferences in REW, if I use "ASIO" my HDMI device ("denon avr") doesn't appear in the "output" drop-down, or in the"ASIO control Panel" If I use the "JAVA" driver, then...
  20. REW Forum
    I'm new to REW and still trying to figure things out. I am running REW V5.01 BETA 22 build 3423 on my laptop, 32bit Windows 7 and don't believe the SPL values I am getting with my new UMIK-1 with calibration file when using ASIO4ALL v. 2. Not sure if I'm doing something wrong or ? I...
1-20 of 43 Results
Top