Home Theater Forum and Systems banner

bash

  1. Classifieds - Audio Equipment
    I have a BASH 300 plate amp that I am no longer in need of. It works great and is in excellent condition. (I have soldered on longer speaker leads to make subwoofer installation easier.) Pictures are available if needed. Here is a link to the product description...
  2. Subwoofer Amps | High Pass Filters
    Does anyone know if the line out of the amp is affected by the highpass/ eq settings? If so that would be awesome.
  3. Subwoofer Amps | High Pass Filters
    High guys, I am building a sonosub with IXL 18.2.2. Volume is 368L tuned to 15hz. When I model this in WinISD cone excursion exceeds xmax around 13Hz without a filter. I know the BASH 500 comes with some boosting and HPF setup. Could someone help me out with the default setup and how it...
  4. Classifieds - Audio Equipment
    Used for 3 months, like new. Comes with power cable. $200 shipped to lower 48. http://www.oaudio.com/500W_SUBAMP.html
  5. DIY Subwoofers - General Discussion
    I have it up and going as of this afternoon. I will post pictures and more info tomorrow. But could someone point me in the right direction for boosting the amp, DB and HZ? Box has a net volume of about 3.8 cu. ft. And using (2) dayton unweighted PRs. Thanks!
  6. Subwoofer Amps | High Pass Filters
    Unfortunately, the Eclipse 10" drivers I have on hand are DVC 4 ohm each. I have two Bash 500 amplifiers. I was going to wire one per driver, but the impedance for each amp will have to be either 2 ohms (parallel) or 8 ohms (series). Even at the supposed 500 watts the Bash amps put out, the...
  7. Subwoofer Amps | High Pass Filters
    I'm actually wondering what kind of HPF this amp use. Is it a 2nd order or a 4th order High pass filter? It is actually important because my subwoofer could bottom out if it's a 2nd order. I'm talking about the bash 500 amp that part express and CSS carry. Not the O-audio one used by SVS. I...
  8. DIY Subwoofers - General Discussion
    Does anyone know where to get a cutout pattern, or what the dimensions needed to mount one? I'm looking at the BASH 300 that PE sells.
  9. Ported Subwoofer Build Projects
    Hello everybody! This is my first time doing this, so bare with me. I just received my parts from Parts Express today. I had to get them shipped to my uncle in Jersey (i'm Canadian:neener:), because the shipping to Canada was ridiculous. ANYWAYS, i'm pretty surprised at the quality of the...
  10. Creative Sound Solutions
    What are some good ideas to build if I use a sdx15 along with a Bash 500w plate amp? Any ideas? Thanks
  11. Subwoofer Amps | High Pass Filters
    I have a Bash 500W Digital Subwoofer Amplifier with the crossover on it modded 25-30 Hzboost(1db) 18.7high pass and a q of 1.0 while putting my Dayton Titanic in a new box it stopped working, I checked all the connections, and whenever I turn it off then turn it back on it has a huge pop. When...
  12. Subwoofer Amps | High Pass Filters
    hey all. looking for more advice! i have a tempest I 15" sub in a ~200L ported box currently being powered by an oaudio 500w plate. i have recently come across a cheap behringer ep2500 and was wondering if i would notice any improvements by replacing the oaudio with it? i only bought the...
  13. Creative Sound Solutions
    I have a Bash 300S when I run the RCA from the sub out on my reciever and connect it to the LFE the adjustable crossover does not work . When I use the right line level input crossover works .Should I split the RCA into the left and right line level or is one of them a Mono channel. I cannot...
  14. Subwoofer Amps | High Pass Filters
    I have 2 BASH amps. An Oaudio 300 and PE 500. The little transformer on both gets extremely hot to the touch when setting idle. I'm guessing its normal since they both do it?
  15. Subwoofer Amps | High Pass Filters
    So i just installed a new from parts-express bash 300S amp for my friend. I did the resistor mod as its an 8" driver and would have over exerted itself without it. The amp sends zero signal to the subs from either the RCA inputs or the high-level input. I have re soldered the resistors onto...
  16. Classifieds - Audio Equipment
    It turns out I need a different amp. I have only used this for two days. In perfect condition but I am not willing to solder new resistors. Here is my build thread: http://www.hometheatershack.com/forums/exodus-audio/22662-tempest-x-2-ez-slot-port-built.html...
  17. Subwoofer Amps | High Pass Filters
    I already own the Oaudio 300. I bought the PE 500 BASH this weekend when it was on sale and cost the same as what I paid for the Oaudio 300. Which of these 2 amps will give the flattest, deepest response with the Dayton RSS265HF-4 10" driver in a 1 cu. ft. sealed enclosure? Will either amp...
  18. Subwoofer Amps | High Pass Filters
    Bash 500 sale Good to Sunday only- thought some of you diy'ers would want to know asap:T
  19. Ported Subwoofer Build Projects
    First of all I'd like to thank Mike and all the other posters here for the help I've received. There's alot of good info here. I've spent more time researching than actually building. Dimensions 21"x21"x42" 7.9 cuft usable internal volume 6" port 24.75" long Hopefully this weekend I'll get a...
  20. Classifieds - Audio Equipment
    Looking to buy a plate amp: Bash 300w, 500w or Dayton 500w. Post what ya got. Thanks
Top