Home Theater Forum and Systems banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 340 Results
  1. DIY Subwoofers - General Discussion
    Hello I have a Behringer NX600D amp that runs two DIY VBSS 18" subs. I have heard of the possible benefits for having the subs connected to the high level inputs (especially if focusing on 2 channel audio, which I am) and thus I wanted to give it a try. Anyways I was hoping to get some advice...
  2. REW Forum
    I did some searching here and a brief amount of reading. I get the impression that I need a calibration file for my Behringer ECM8000? Any helpful hints? Regards, Dan
  3. System Setup and Connection
    HI, I'm trying to digitize some vinyl using a Behringer UCA202. I see the signal in Sound Settings and I can plug headphones into the Behringer and hear the music. I am not hearing anything through my computer speakers. I'm not sure where to look on my computer for the signal. I have Audacity...
  4. Subwoofer Amps | High Pass Filters
    Hi, I would much appreciate to confirm what is the proper interconnect cable for the Behringer iNUKE 1000DSP? Currently I am using the following XLR to RCA cable...
  5. Pro Audio
    Gday guys. im new here and this is my first post.. apologies if its not in the correct place. ive rackmounted alot of amps and pro audio gear in the past always going off the rule of thumb to "stack the heavier items below to support the weight of the rest" especially when there are no rear...
  6. Ported Subwoofer Build Projects
    I'm building a pair of subwoofers for my home theater based on the mentioned amp. As soon as I turn on the amp I get a lot of humming noise. I did some Google research and learned that a unbalanced/balanced converter can eliminate noise. I also browsed some Pro audio websites and found a hum...
  7. Subwoofer Amps | High Pass Filters
    Hey Shacksters , I am currently running a Crown XLS2502 2 channels at 775 @4 ohms per channel with 2 Ultimax 12" Dayton audio subwoofers in sealed 2.0 cuft enclousures. Is the Behringer I-Nuke NU6000DSP boasting 2 channels @4 ohms 1500 watts RMS and 3000 watt peaks per channel really have...
  8. Classifieds - Audio Equipment
    I am selling one of my two EP4000's which was used to drive one of my DIY sealed subwoofers. I've had it for about a year but have only used it for a few months. I simply do not need two of these for my setup, one works just fine, and I'm trying to clear up some space on my equipment shelf...
  9. Electronic Processing/Equalization Devices
    Behringer processor fault and fix: DCX2496 I am posting this just in case it can help someone searching this forum in future. This info may already be in some other part of this forum, in which case my post just reinforces the statistics of the fix. My DCX2496 suddenly developed a fault -...
  10. Home Theater Receivers | Processors | Amps
    Not surprised...
  11. Home Theater Receivers | Processors | Amps
    I have had my Behringer iNuke NU6000 for right around a year now. The loud fans have always bothered me when listening at low levels in my HT. Just last week I made an upgrade in my AV cabinet to include some more powerful fans. The result was the cabinet air temp right above the AVR runs at...
  12. REW Forum
    Hi there, I'm just getting started with using REW and practised taking some readings using an AKG CK61 ULS Capsule (probably not great to measure) but just to get used to the process - I'm getting there. I now have a Behringer ECM8000 - So two quick questions; 1) I have downloaded the...
  13. Classifieds - Audio Equipment
    I am selling 3 perfect physical and functional condition Behringer EP2000 units, just over a year old. I purchased them new from Parts Express in May 2015. The fans in these units run loud, and since I used the amps at relatively low power in my home theater only, I performed the Digikey fan mod...
  14. REW Forum
    I want to equalize the monaural sound system of a school auditorium. Does the Behringer DEQ2496 (a current model) work well with REW and would it be suitable for this? Thank you.
  15. REW Forum
    When I try to program an FBQ2496 via midi from REW the frequencies of each parametric a slightly different from the actual ones in REW does anyone know why this would be?
  16. Subwoofer Amps | High Pass Filters
    Hi! Im planning to buy inuke nu3000(dsp) or nu6000 to power my single 12" 1500w rms subwoofer. So the question is does nu3000 give enough power? Does it give 1500w rms or what is the irl (In real life) power? If nu3000 doesnt give 1500w rms or more i have to think of buying nu6000. I dont want...
  17. Subwoofer Amps | High Pass Filters
    I need and amp to run two different subs in my HT rig. I've got a dual Parts Express 15 driver infinite baffle and a sealed Tempest sub. I would like to drive each off a different channel of the same amp. The amp would see a 4ohm load on each channel. IB drivers wired parallel and the Tempest VC...
  18. Home Theater System Recommendations
    As I have posted before. I own one Behringer 3000 DSP amplifier. I have been testing it and it sound pretty good so far. I have one 8ohm 1500 RMS dual speaker which I have connected in channel B. I have set the amp on stereo mode which feed the speaker with around 450 RMS. So i went and put it...
  19. Electronic Processing/Equalization Devices
    After some discussion about EQ solutions for various applications in another thread, I found myself in a unique position to get some impressions of the FBQ-1000. It was alleged that the old model, the Feedback Destroyer DSP1124P, was noisy and therefore unsuitable for use in equalizing L/R or...
  20. Electronic Processing/Equalization Devices
    The DEQ2496 front panel is connected to the main unit by a short flat cable. You can use the front panel as a wired "Remote Control" I extended the short flat cable with a 5 Meter flat cable and this way I have full control of the DEQ2496 when I am sitting in my listening positioning in my...
1-20 of 340 Results
Top