Home Theater Forum and Systems banner

bottom

  1. REW Forum
    Hi, Ive been learning so much here. Thanks for all of the knowledge and help! Im hoping for some guidance with respect to boosting the bottom end <20hz of my sealed subs (they are Epic Empire 8ohm drivers in 1.64cuft = vb and stuffed with R13 about half way) powered by an inuke 3kdsp bridged...
  2. Home Theater Design and Construction
    Hello, I am trying to install a set of 5.1 speakers in my family room. The family room is like an extension to the house with vaulted ceilings. Hence both the front and the rear speakers are on external walls. I have first tried to install the rear speakers, where I am stuck. The intention is...
  3. Sealed Subwoofer Build Projects
    I was going to build a sub with the Stereo Integrity 15" d2 sub Any help on ported vs sealed???
  4. Panasonic / Technics
    Hello the image shows red 1 half X 1 in red blinking pixel squares with small amount of green inside red on top of screen and bottom only. They are about 1.5 inchs apart 2 rows vert from left to right the center of screen is good . This is in all inputs except when u select cable then the...
  5. Samsung
    I repaired the power supply on a 56 inch Samsung flat screen but now I have this band on the bottom. I have a picture but do not think it will show until I have posted more.
  6. Pioneer
    I have worked on TV's for 10 years and have stopped working on them along time ago,I never was good on big screens i always dreaded them.And now i have a problem myself.My big screen.I come home tonight and see that the green is bowing up from the bottom.Just the green the red and blue is still...
  7. New Member Introductions
    Hi, everyone. Thanks for this wonderful site.... I managed to download and install the REW. It works and I'm absolutely amazed. By trade, I'm a weldor....but in spirit an audiophile and musician. All I can say is "if anyone lives in my area, fully understands how to use the REW, I'll...
  8. REW Forum
    Hey room, I just purchased a Mac Pro Dual 2.8. Prior to this, I had a g4 which I could not use Room EQ on I was told because the G4 didn't have audio ins and outs. The Mac Pro does. I have a MOTU 828 Mark 1 that I'm using as my audio interface. I also have the Radio Shack SPL analog meter. I...
  9. SVSound
    Hi all gurus, I need some advise from you about calibrating my 20-39PC-Plus using 12.3 driver. As commonly know that "Flight of the Phoenix" (FOTP) has some of the loudest bass measured in the 20-35hz range. And I am trying to push my sub to the limit but without bottom out when it play FOTP...
  10. Mitsubishi
    I have a Mitsubishi 46" Rear Projection WT-46805. The top and bottom of the screen bows almost like a sideways hourglass. I've read the convergence thread and figure I need to replace th IC's. Is the a way to know if just resoldering will fix the problem. Also I have found out that if I tap...
  11. DIY Subwoofers - General Discussion
    I'm about to start my "twin tower" project, using 28" sonotube and 2, RL-P18 drivers. What I'm not sure about, though, is what exactly you do with the ends of the "sock" you make from fabric to cover the tube. Can somebody point me to some pictures of someone else's build that shows exactly...
  12. Home Audio Subwoofers
    OK, I just started watching "The Matrix: Revolutions" on HD-DVD, using Dolby TrueHD via analog connections, and something kinda disturbing just happened (I shut down until I can determine what). During the explosion after the title screen, a loud "pop" eminated from one or both subs (I can't...
  13. DIY Subwoofers - General Discussion
    Im just wondering what the consensus is on if a sub box should be spiked. I would think it would be a good idea for strength and tranfer of energy, but then again my box/sub will weigh in at about 60 pounds. Thus i would think i would need atleast 6 spikes to distribute the weight around...
Top