Search Results for ‘crossover’

whats a good crossover point to set for these from the receiver i was going set to 50hz, my current config is my fronts are at 70hz an my center at 60hz , would 50hz on these Rockville SPG88 for use as sides an a pair set at 60hz for rears be good i'll be driving each set with a crown xli...

I’m looking for a sub that has left and right RCA in and out, and further that acts as an active crossover (thus not sending the bass that the subwoofer is handling to the main speaker amps). The reason for this is that I have a great stereo pre-amp with only one pair left and right RCA...

Hello, Helping my friend with this setup replacing V995 setup with crossover to AS710. I'm not experienced with a crossover so need some help here... When I connected speaker system as it was wired on V995 the 2 rear speakers are not working. I will run YPAO tomorrow but I'm not sure if I...

does anyone know if both the BIC Venturi DV84 an dv64 inturnal crossover can be replaced with the Dayton Audio XO2W-2K 2-Way Speaker Crossover 2,000 Hz

I'm looking to buy 2X4 DSP, or single unit that is larger. Prefer boards, but for the right price, I'll crack the case. (this is for an amplifier build) Please contact me with what you have available. Thank you.

I am having some deep technical issues with my TSi500s that I have had for a good while. Signal chain: Laptop->Steinberg UR22MkII-> Yamaha 1065->TSi500. Using a Dayton EMM-6 and REW for measurements I setup REW to do some room measurements, and noticed a severe dip in my high frequencies...

I wish to use REW for testing passive crossovers. I have attached the file herewith of the setup. How to calibrate now REW with this setup? Any suggestion/guidance regarding setup & calibration is required.

whats the best crossover fq to use with this my preference is 70hz to 50hz any thoughts my fronts are BIC Amercia Acoustech Platinum Series PL-89 tower set at 65hz https://www.amazon.com/BIC-Amercia-Acoustech-Platinum-PL- 89/dp/B001VIXH7I/ref=pd_sim_23_4...

For years, I wanted to design my own speakers, but didn't understand the intricacies that went into it. For all I knew, you bought a 2500 hz crossover from parts express, picked a woofer and tweeter that looked cool and went at it. It wasn't until i really got into DIY speaker building that I...

im lookinn to build a powerful 3 way crossover for a floorstanding speaker 7 driver design able to drive 300watts to a pair of 2in tweeters an 3 8in midrange woofers an 2 8in lowfreq woofer my planed design inclueds these parts 4- Jantzen Audio 8.2uF 400V Z-Standard Capacitor 2 left an 2...

Are there any options for crossover design software that gives design iterations/optimization like Soundeasy but is less expensive and/or more intuitive? Thanks, George

Hi All, I would like to ask a general question about room correction: What shall be the ideal order of the followings: - Room correction EQ - Speaker distance setting - Level setting - Crossover setting Currently the order I have is the following: Crossover -> Distance -> Level -> EQ But I was...

Hey! The question is related to a soundcard feature, so i iope i am posting in a right section. I have a Asus Xonar DGX sound card, which is pce-e based, 5.1 card. I want to use it to set up a 2.1 system. I have a stereo speaker system with its own integrated amp and a subwoofer with an amp...

I was trying to display multiple measurements / phases to align a mid-hi crossover, based on a selectable common measurement minimum phase display, and wasn't successfull… Can someone point me in the right direction ? ( Sorry to say, I'm used to Smaart 5 ) Thank you very much and best regards Klaus

I have been working with DIY audio for years. I believe my understanding is somewhere in between intermediate to advance in terms of theory. I built my own home theater system and the goal was to stay moderately cheap. I used Dayton reference series for all my drivers. I'm happy with the overall...

Hi all, I've been having some issues with Audyssey crossover settings lately. My current setup is as follows: - Speakers : Chane Music & Cinema A5rx-c towers and A2.4 center - Seating position is 10' from the TV - Room size is 12' x 16' - The L/R speakers are 8' apart on each side of the...

I am currently building my entire home theater from scratch. I am designing the crossover for my center channel and wanted to know which of the two would be better and why. I am using HT Audio Xover 3 pro. The "4th order" attached image is a 4th order LR for the high and low pass. i tried...

I am looking to purchase one these this fall when the price drops and am also looking to go with active crossed separates. Was hoping I could use the receiver to power tweeters and use other amps and mini dsp for mids and woofers. MY question is what crossover frequencies are available for the...

Is it possible to use measure with REW, in order to find what the crossover frequencies of a Passive 3-Way speaker are? Thanks