Home Theater Forum and Systems banner
dcx2496
1-20 of 45 Results
  1. Electronic Processing/Equalization Devices
    Behringer processor fault and fix: DCX2496 I am posting this just in case it can help someone searching this forum in future. This info may already be in some other part of this forum, in which case my post just reinforces the statistics of the fix. My DCX2496 suddenly developed a fault -...
  2. Electronic Processing/Equalization Devices
    I recently acquired a Behinger DCX2496. It has 3 inputs and 6 outputs and has some powerful EQ & Crossover options. Here is my theater thread for an equipment list I don't have any horrible EQ issues, but I have a UMIK-1 and am considering using the DCX2496 for its crossover and parametric...
  3. Electronic Processing/Equalization Devices
    Got a question for the DCX2496 owners. I have one sitting around, so I would like to use the eq part for my mains and subs. Can route full range from "A" input to "1" output "B" input to "2" output and so on?
  4. Electronic Processing/Equalization Devices
    Is anyone familiar with both the DCX2496 Ultra-Drive Pro and the DEQ2496 Ultra-Curve Pro Mastering Processor ? I have had the Ultra-Drive pro as an Electronic Crossover for the Newform Research speakers according to the manufacturer's instructions, for about ten years. I was using a Meridian...
  5. Electronic Processing/Equalization Devices
    I have a pair of Mackie HR-824 active monitors and although they have very good response (39Hz - 20kHz +/- 1.5dB), I would like to add a sub to reach down deeper. I'm thinking about adding a Rythmik F12 or F12G, but my source device (M-Audio FW410 recording interface) does not have any bass...
  6. Electronic Processing/Equalization Devices
    replaced my broken DEQ with the DCX, and now I cannot find anywhere (manual, online, etc) on how to setup a simple stupid low pass shelving filter at 6db/oct :hissyfit: I know I'm being a m0ron and it's likely right in front of me...can someone be kind enough to show me how to do it from the...
  7. Pro Audio
    I would like to use the dcx for crossovers and filters for consumer/home use. I have a 7.2 sys. and don't know how far I can go with 1 unit. My subs I will use the deq and for the others (7 speakers) the dcx. Will I need more than 1 dcx? Is the mx882 recomended? For the low volume noise...
  8. Electronic Processing/Equalization Devices
    Does the DCX2496 connect to REW? I may have the wrong end of the stick here, I can set the equaliser to DCX2496 for EQ band purposes, but I thought that REW talked to them via RS232. The help files say that there are only two processors it talks to by serial link (AV32R & AV19R), so I am...
  9. Electronic Processing/Equalization Devices
    I am wondering if anyone here has modified their DCX2496 and has any stories or feedback they can share. There are lots of mods floating around the internet, and some that will do the mods for you (at quite a price). I use my DCX2496 as an active crossover for my system, but it is audibly...
  10. REW Forum
    hi, this is my first post in this forum, i expect to dig deeper and deeper in REW in the future by practising. today, i just got TASCAM US-144MKII together with behringer DCX2496 arrived in my home. with my radioshack 33-2055 SPL, i'll be able to perform REW measurement during following...
  11. Classifieds - Wanted
    I'm looking for a DCX2496. Looking to spend about $175. I don't really care how it looks as long as it is fully functional.
  12. Electronic Processing/Equalization Devices
    I know that a Linkwitz Transform draws a massive amount of power, but how does that happen if it is implemented upstream of the amp in a DCX2496? I want to make sure this will work before I implement it.
  13. Electronic Processing/Equalization Devices
    I have 4 subs that aren't placed symmetrically in my basement. I got a DCX2496 for cheap and want to use it to set individual delays/phase/distances for each sub individually prior to running Audyssey. I am rather proficient with REW v5 in regards to running frequency response graphs and...
  14. REW Forum
    I just purchased Behringer DCX2496 and used it with REW. Everything went fine until I couldn't decide how to transfer the EQ Settings in REW to DCX2496 (I have also selected DCX2496 filter setting under REW). I connected my DCX with USB-Serial Cable under Win 7 successfully. There were a few...
  15. REW Forum
    I just wanted to compare DSP1124p and DCX2496, setting up a DCX2496 eq with the same measurement, but the REW eq parameters aren't the same as in the DCX2496, this could be verified in the remote software for the DCX2496... There could be a reason for this though ? John ? Thanks Klaus
  16. REW Forum
    With USB to serial adapter, it is possible to 'simulate' rs-232, i.e. Shure workbench, elo touchscreens, etc could this be possible with REW, to control DCX2496 ? Klaus
  17. REW Forum
    I saw a case study that provided good information regarding this subject for aligning the SW to Main speakers. The method I use for aligning a MR (aka MW) to a TW is somewhat different so here it is. This example uses a DCX2496 for XO and driver delays, but the process will be similar using...
  18. Electronic Processing/Equalization Devices
    I am running source --> SRC2496 --> DEQ2496 --> DCX2496 --> amplifiers --> speakers 3 way stereo (6 channel) triamp. I want to use REW to EQ the low end, as I understand this is more accurate than letting the RTA on the DEQ handle these frequencies. As both the DEQ and the DCX are capable of...
  19. Electronic Processing/Equalization Devices
    If a mod wouldn't mind moving this to the appropriate section. I didn't mean to post in Manufactured Speakers..
  20. Pro Audio
    I know that there have been a number of threads about DCX2496 vs alternatives - but can anyone give me a reason not to buy a DBX Driverack PA/PA+? I was about to buy a DCX2496, but after reading about some of the "frying egg noise" problems, the bug that some seem to experience with the D/A...
1-20 of 45 Results
Top