Search Results for ‘drop’

We just purchased a new home, and I am trying to figure out how to make my old 195" 2.35 aspect fixed AT screen drop down in front of our windows/doors. I would ideally like to have the screen drop down in front of my speakers, but that would mean extending the screen mount out 3' to clear the...

This is an experience that has had me frustrated for some time now. Hope it helps some others as well. The problem was streaming Tidal 'Hi-Fi' through my computer. After doing simple test tones I found a huge dip centered at 60hz. Very little sound coming out at this frequency. Most...

Hi guys. I am just getting started with REW and was trying to get some baseline measurements done. The good news is my baseline setup looks pretty similar in shape to the recommended house curves. The odd thing is that no matter what I do with the speaker position, I get about a 30db drop...

Hi, I had performed a stereo measurement of my floorstanding spk at my listening position. Spk = monitor Audio pl200 Pre = ATC LS27 Power = DIY Hypex Ncore NC400 Attached is the dB vs freq curve. As per the title, it is common for the high freq to drop in such a way ? Attached the rest of...

Vizio recently released a much needed firmware update (v2.0.13.13) for its SmartCast P-Series and M-Series Ultra UHD 4K televisions. When downloaded and installed, the updated enables support for the HDR10 format standard found on select Ultra UHD Blu-rays and streaming content. Vizio now...

I'm embarrassed to admit how long it took me to realize that the casing for my Stewart Filmscreen (LX092HST13G3BM) was ringing. I kept hearing something 'odd', but it wasn't until some recent changes that I realized that the screen casing was the culprit. Wrapping the outside with FatMat solved...

Would it be possible to have a smoothing indication tickmark in the Graph drop down menu? You can see this information on graph legend but when choosing smoothing this is unconviently quite far away. Even two different smoothings could be chosen for comparison! I use this quit a lot by opening...

Here is a ten step guide for making cheap 2" thick fiberglass broadband absorbers with a 2" air gap from materials easily available in Thailand. At the bottom of the post are guidelines for using panels as ceiling clouds and for installation in front of windows or other obstructions that can't...

Hey all, I was playing around with REW to measure my sub performance in my finished basement. I'm running two old SVS CS 16-46 cylinders powered by a Samson S700 amp. I normally have them split with one up front and one to the side of the MLP. I"m pretty limited in positioning as this is a...

I'm trying to find the best spot for my sub using with my laptop with HDMI out to AVR and USB SPL Meter (RS) to my laptop. I notice that the dB reading is highest after I calibrated SPL meter then it would slowly drop off as time goes on. I just lost 10 dB after 10 minute of waiting without...

i have a Motorola DCX3501-M cable box. Are their known issue with audio drop outs. I am using a HDMI from audio quest( i would like to think its not the cable) i am in the process of trying different cable. I get audio drop out over the HDMI cable. ( im testing the Optcal now) Is it the...

The popularity of 3D television just didn't hit the mark, in general at least, and that remains true in the world of sports. ESPN plans to discontinue it's 3D channel by the end of this year, an experiment they started in 2010. With the 3D exit, ESPN has plans to jump past 1080p and and...

i am having some problems with my a/v unit. if i listen to music all 5 channels work prefectly fine!! but the last couple times i try to use my set up mic i can never get the left rear channel to calibrate. any ideas on how i might beable to fix this??

I hope I can describe this issue effectively. I have been using REQ for quite some time, so I am reasonably familiar with its basic functions. My REQ kit includes a Soundblaster X-Fi USB soundcard, an EMM-6 calibrated mic (with custom calibration files provided by Spectrum Labs), a Xenyx 502...

Im getting close to the drywall stage of my build and thats puts me close to the ceiling part. Im doing a drop ceiling. Is there any special criteria or things to look for or avoid when choosing ceiling tiles? Im going with a black ceiling for sure. This is one tile ive been looking at...

Recently, for no particular reason, the left channel on my amp has stopped working. I've checked the speaker cable and the speaker and these are working fine. It a complete mystery and I was hoping some could enlighten me as to why this is happened.

Are there any owners of a Favi electric screen that can tell me the max drop? The web site shows 5.5 inches, but can it be adjusted?