I am selling one of my two EP4000's which was used to drive one of my DIY sealed subwoofers. I've had it for about a year but have only used it for a few months. I simply do not need two of these for my setup, one works just fine, and I'm trying to clear up some space on my equipment shelf...
I don't really care about DSP at this point, if I need it I'll use a software or a miniDSP, I'm looking for raw power and speaker control. What would be best? Behringer NU3000DSP or EP4000?
I have also posted this on another forum but, so far, I have not received a reply. I hope someone has experienced a similar problem and can advise me.
I recently modded my EP4000 and installed a quieter fan. I cut the existing wires and spliced in a new fan using a connector to tie the new fan...
Hey guys,
looking for help with this set up ,i have EP4000 driving single 12' Dayton Audio Ultimax DVC Subwoofers wire for 4 ohm in seal box for one month and suddenly CLIP light turn on all the time and no sound if i disconnect sub to EP CLIP light goes away .called Behringer and send it for...
couple questions I am looking at upgrading my Keiga 52100 plate amp to a EP4000 amp or the sorts. I am running Passive radiator setups in my builds. My question is that I read the HPF is defeatable on the amp. If this correct and is it as easy a switch. I would like to have it set around...
I just received a new Behringer EP4000 to power a pair of DIY subs. I've seen several references in threads dating back a few years to improper labeling of the DIP switches on the back of the unit and/or within the manual. Does anyone know if this has been fixed by Behringer? If not, where we...
I need your help. this weekend there are a lot of labor day sales. the ep4000 is everywhere for $379.00. is this a fair price? I'm building another sub and I cannot afford another qsc2450. 4 years ago I got it on sale new for 479.00. I cannot find one for less than 800.00. but this seems like a...
Quick question, I currently have 2 EP4000 which would drive 4 SI 18" (D2 wired for 4ohm) in 24" sealed boxes. One sub per channel.
I got the Class D bug and picked up some XLS 1000 and 2000 to drive my speakers.
I was thinking of replacing the EP4000 with some XLS amps.
How much power would...
Quick question.
I recently EQ'ed my subwoofer and set my sub levels. My AVR sub level is at -10db, miniDSP (.9v to 2v) is at -8db, and EP4000 is at 16. I was watching a movie a -odb and I noticed my clip light would flash at large at large hits. I had to turn down the volume to -7db to...
I was wondering if there was a way to shutoff my ep4000 other than the switch on the front. I can shut down my whole system from my onkyo remote but always have to go up and shutoff the amp. I was just wondering if anyone has any ideas for this. I'm especially asking because I'm putting a...
Looking to buy a fan today for modding my EP4000 and need help quick...
Will either of these fans work, and if so, which one would be better????
Fan 1
Fan 2
Good day all ,
I was playing with my new TX-NR818 and after talking to a Behringer tech specialist they had me setup the dip switch as this
RIGHT - clip limiter ON
RIGHT - low cut filter 30 Hz
LEFT - low cut filter ON
RIGHT - parallel operation
RIGHT - parallel operation
RIGHT - bridge mode...
I have a Behringer EP4000 I wanted to test the power output on first to see how it relates to the factory specs., and have been too busy to do it yet. I've been having a hard time figuring out if I want the SI HT D2 or D4 versions. I'm leaning towards the D2 as it will give a bit of overhead...
Goos evening all
i would like to have your toughts on using either the ep4000 or ep-2500 as amp to power main speakers in a home theater instead of consumer amp like emotiva, marantz ect
For the amount of power provided it seems more economical but is thre any pros or cons going that route...
WTB a behringer ep2500 or ep4000 for a ht setup. also if you have a inline voltage converter for sale also i would be interested in purchasing that also.
Could anyone help me understand how the numbers on the gain control relate to output wattage?
I have my first of two enclosures built and am a little anxious to hear or feel the outcome.