Search Results for ‘eq’

Hi, My graph is a bit unusual. Can you take a look? I'm using a 5-inch book shelf speaker.(JBL) As you can see I have a dip of 100 Hz on both sides. However, it seems that 70~90hz is too low, except for the dip of 100hz.(Especially the left speaker. I tried to apply EQ only below 200hz to...

Does any one works with Mathaudio Room EQ or could make an comparison with other Roomcorrection software. Found it quite simpel to work with incomparison with REW The results are for me excelent. I work with Mathaudio in combination with Foobar2000 no cost involve.

Does any one works with Mathaudio Room EQ or coukd make an comparison with other Roomcorrectio sofware. Found it quite simpel to work with.results are for me briljant. I wirk with Mathaudio in combination with Foobar2000 no cost involve.

So i've translated frequency response graph from picture i found on the net.I've did it with webplotdigitizer.Now i want to load that graph(text or csv file) into eq vst that can read these settings ,what eq should i use,i've tried Curve eq but it cant read it well like it have some different...

i have the dv84 as my fronts an two of the PL-28II as centers does anyone know whats the best config for outlaws 976 eq for the left right an centers each has a two shelves and eight bands setting an its a bit confusing for me since i dont know what shelve a an b are for an how to configure...

Hello everyone, This is my first post here, I've lurked the forum from time to time as I've begun my home theater journey. More to the point... I've been playing around with REW over the last couple of months in my free time. I've been having a few issues that I'm struggling to figure out...

Hi everybody After getting a new set of speakers "dialed in" to my "man cave", I purchased a new pair of sub woofers for that last octave of bass. In the past I've had to be patient, integrating a sub with a pair of monitors, to get them to sound "just right", adjusting the positioning of the...

I have a friend visiting from interstate, he's trying to help out with REW etc and limited time so I apologise for not having read through the mountains of info trying to find the answer I have a Yamaha RXA 3070 receiver so using its inbuilt eq- it has parametric eq with 7 bands- from memory...

I got an XTZ 99W12DSP subwoofer which has 5 parametric EQ filters and 10 graphic EQ filters. For REW, I pick the "Generic Equaliser" and setup 5 Auto PK filters and 10 Manual PK filters with the 10 static frequencies and the Q-value of 5.1. I then run the "match response to target" and then...

I ran some sweeps with my subwoofer at 10 positions and then did an Average for those which I then use to create EQ filters. The Average looks pretty much as the middle most position of my sweeps so is there more "information" to work with for creating the EQ filters with the single...

Problem with simulation of Frequency Response with EQ Filters In order to investigate the impact of the EQ Filters into Step Response, ETC, T60 and so on, I've tried to obtain an impulse response of my mesaurement with EQ Filters applied. To do so, I have followed these steps: 1) Export EQ...

Hi, I'm looking for a USB DAC that has the ability to EQ the music as well. I have been using an iPhone 6s for music with the Focal Listen headphones, but hope using a DAC with a laptop might have a little better quality. My price range is around 200, any ideas? Thanks, Nick

i need some advice i have a 3 Crown XLI800 to drive 2 BIC Acoustech PL-28II Center SpeakerS ,2 BIC Amercia Acoustech Platinum Series PL-89 tower speakers ,and 2 BIC America Venturi DV84 2-Way Tower Speakers at 200watt do i need ART CLEANBoxPro 2 would that help i have Rockville...

Hi All, I would like to ask a general question about room correction: What shall be the ideal order of the followings: - Room correction EQ - Speaker distance setting - Level setting - Crossover setting Currently the order I have is the following: Crossover -> Distance -> Level -> EQ But I was...

Hi all Hopefully you can suggest some help for me please. I'm new to REW and wish to use it for impedance measurements. I have a set up problem that I can't find any advice on how to solve this. I have a Soundblaster SBX ProStudio and Windows 10. I have set up the Soundblaster in the...

Have untreated spare bedroom with only a desk and desk -- for voiceover/tutorials. Room has hardwood floors with a rug, bare walls. Just purchased a dbx RTA-M mic and used it with my laptop speakers (buying a small pre-amp to run speakers from laptop today). For setup, I ran XLR from the...

I have a (listed above) sub that was given to me. the cabinet and sub are in good condition, however the amp is toast. I was wondering if it is viable to use the old cabinet and get a new amp or build a new cabinet and get a new amp? the sub only has the word Velodyne on the back of the sub so...

For sale 4 dual 4ohm RL-p 15 subs 1 Behringer EP2500 fan mod. 1 Behringer dsp-1124. Trying to sale as a package $1000 for all. Contact me @334-782-3610. Pick up only unless you want to pay for shipping.