Search Results for ‘fbq2496’

I have encountered a bug with REW and the FBQ2496, affecting all EQ settings that are sent as BOTH channels to the FBQ. It's most noticeable with a full-range signal. After sending EQ settings via 'both' channels (not separately) to the FBQ via REW, a power cycle of the FBQ will introduce an...

When I try to program an FBQ2496 via midi from REW the frequencies of each parametric a slightly different from the actual ones in REW does anyone know why this would be?

First post out side the Post Padding Thread and first forum post in a long time. So since the BFD Guide link seems to be broken or taken down, I need to post a question. Received a New FBQ2496 in the mail today and inserted it into my system, after the pre and before the amp. Used all XLR...

Hi! Just got a new FBQ2496 from the store. Firmware 1.1. FBQ2496: Enabled midi and channel 1. Run mode. Connected as described i help menu REW 5.13. REW: Preferences set correct on all tabs (I think). UM-1G connected to usb and installed ok, set to Passthrough off and Advanced off. UM-1G is...

I am using a Beehringer FBQ2496 along with REW 5 to eq my subwoofer. And today the girlfriend was vacuuming and accidentaly hit some button(s) on my FBQ2496 with the vacuum cleaner. Now the front display is showing this: instead of the normal display of my 5 filters applied to the topmost...

I have tried to eliminate my room modes with REW in generic mode, APO equalizer, Laptop onboard sound card, behringer ecm8000, behringer xenyx 802 and pioneer 1018. Although i finished the process and the curve seemed satisfactory, the real world result was dissapoiniting. I tried raising bass...

I am using REW and an FBQ2496. I transmit filters via midi and every filter has to then be manually adjusted because they are usually off by several digits... (only the frequencies). Does anyone have any idea why I am experiencing this?

I have a MFW-15 in my small media room that I am finally getting around to EQ'ing as my Turbo Kit is on its way. I have been using Audyssey exclusively to tame the resonances up to this point. My buddy has a SMS-1 that he is going to let me borrow and I’m going to purchase a Feedback Destroyer...

Dear all, I have a mixing room in which I have to correct some frequencies. I did son room treatment to reduce reflections on medium-high frequencies but still I have some issues on the low end (standing waves). At the moment I am using parametric equalization via a software plugin and the...

I have been fortunate enough to have someone kindly build me dual 18inch sealed subs to replace my PB13U. I have a lot of work to do with the response as it is all over the place and I have no room for movement with the location of these subs due to their size. So an eq device is the only way...

hi, I would be very thankful if a fbq2496 owner could give me the chemical capacitor values on the fbq2496 processor board. I was in the process of modding it and removed all caps without paying attention that there was no label about values, which is the first time I see that in behringer...

Hello all! I bought a FBQ2496 to eq my subs today. I want to order all the cables to go with it but have a few questions on the connectsions. I appoligize if this has been covered already, if so, can you point me to the correct thread... Equipment in question is: Pioneer Elite VSX-21TXH >...

Hi, I bought the fbq2496 yesterday. now, what i recogniced is that : (hard to explain, stay with me (; ) if i play a song where a constant 25 Hz tone is played in the background with NO EQUALIZION APPLIED (or bypas mode) the tone/excursion of the membrane/signal light on the ep2500 is like...

Bought this a couple years ago and never used it. It is still new in the box. Looking to get $100 plus shipping. Paypal add 3%

Hi I'm just about to buy a fbq2496 or a antimode 8033c and wonder evigt of Tham you guys would pick? I have two diy 150l subs with shive-x 12" and a passive 15" in each, powered with a tamp ta 2400. I have never calibrated a sub before. I'm want to get the best result, don't bother in spending...

My FBQ2496 is expected to arrive tomorrow YAY :) Have been reading the FBQ2496 manual (which was a bit "thin" I think) + the BFD guide here at the shack. I plan on programming it via MIDI. My questions are mostly about initial setup of the FBQ2496 prior to programming the first filters...

I have everything swithched properly according to all the info ani I hit send filters to eq, it appears to be loading the FBQ. But when its finished the FBQ does not show any filters. Whats up? Thanks, Rick.

Guys need some help on the setup of BFD. My equipment as below: Receiver Onkyo 805 (volume at -5db and LFE level at 0db). RCA cable with 1/4" Mono plug to FBQ2496 left channel input. -10db input switch is on. BFD Output using 1/4" Mono plug and RCA cable to ED A7s-650 subwoofer. I had manually...

SOLD, SOLD, SOLD

Hello, I'm brand new to the HTS. I am currently running two Paradigm PS-1000's on opposite sides on my room. Read the BFD guide and plan to add some subwoofer EQ to my setup. Trying to choose between the DSP1124P and the FBQ2496. I read the manuals for both units and have two questions: 1...