Search Results for ‘fullrange’

I started this thread over in diyaudio.com but thought folks over here may have an interest in it too. It started off on a whim with me asking myself does the namesake speaker from B&W really sound nice because the spiral absorbs the back wave? Why not try it out on a smaller, cheaper scale and...

I recently got a new AVR, so I retired my old one to my office/computer room. I found some old satellite speakers that I have from a few years back (sub and amp for them are long gone) so I pieced together a system with them and the AVR. The speakers themselves use 3" paper cones with solid...

I have 7 FR10-4 with the following specs, Rated power 30 W Maximum power 50 W Nominal impedance Z 4 Ohm Frequency response 80–20000 Hz Mean sound pressure level 86 dB (1 W/1 m) Opening angle (-6 dB) 113°/4000 Hz Excursion limit +/−4 mm Resonance frequency fs 92 Hz Magnetic induction 0,95 T...

Digital parametric with at least 6-8 filters would be nice. Compatibility with REW's EQ feature would be awesome!! Also....need XLR or 1/4" outputs as its for studio use. Been reading about the YDP2006. Is that the best/only contender? I need to give it another look. It's slightly above my...

Source: TWICE

Hi everyone, Trying to do a similar frequency distribution between drivers as in a full size cinema and have been toying with the idea of a 12" prosound driver for 80-500hz and use a mid size full range above. In a true cinema, above 12k is usually rolled of a little, sometimes deliberately but...

Hi all. I'm looking for some full range speaker opinions. I need this to be a lower costed set of speakers ($250ea max). I've beem looking at Mark audio, Dayton and TB. This also needs to be at or near 8" in diameter. The speaker will be used in a Dipole arrangement. If anyone has an opinion...

I checked this sticky thread but apparently its all sub-eq's: http://www.hometheatershack.com/forums/bfd-electronic-equalization-devices/11946-bfd-alternatives-fbq-sms-1-dcx-more.html Looking for something to EQ full-range studio monitors for a recording studio. I'd prefer 1/4" in/outs but I...

I am using a convolver quite a while now to correct my room. I was using DRC to generate filters and now tried REW generated filters. Speakers are KRK RPG8 (Rokit 8) studio monitors. These are active and bi-amped. Here are the graphs:

Hey guys, I am newer to designing loudspeakers and have a certain Idea for a large 2 way speaker. I am looking at running 8 full range drivers for my mid & Highs, and 4 10" inch subs on the lower half of each speaker. This will all be one large speaker, and I will be building a like one for the...

Finally got around to doing a full range measurement of my setup with a calibrated Dayton EMM-6. Using antimode at the low end combined with a housecurve done with EQ. Also got three or four moderate, broad EQ bands higher up. The peak at around 600hz appear to be a feature of my B&W 804s...

Here is my current setup: Sub: Double 12" Passive Radiator crossing over at 80 Hz. Front low Left and low Right: Anthony Gallo Adiva Ti' Receiver:: Onkyo 607 Im after two new units which will be used as my upper left and upper right. Assume that this system will be used entirely for music. Im...

Hi All, I'm getting really interested in speakers, speaker building, subwoofer building, etc. The question the keeps coming to mind is why would I buy/build a full range speaker or even a speaker that extends below 80 Hz when we all know how much we all love subwoofers here on HT shack. Seems...

Hi! I just bought the BFD and the ECM8000 mic, and is wondering how best to apporach the measurement. I have two fullrange speakers in an asymmetrical room (one speaker is closer to a corner than the other). Should I calibrate using 1 measurement from the listening position and store the same...

What is the most current (and thought to be most accurate) "full-range" cal file for the 33-2050 meter and where may I find it? Thanks. PS: Did some searching and found only cal file for bass correction factors.

All, I’m trying to tame a very live room and I’m having a little difficulty understanding all the information I’ve got with Room EQ Wizard. I understand the frequency vs. SPL plots, and the waterfall is very helpful, but I don’t understand the impulse display screens. In particular it doesn’t...

Is the Beringer Feedback Destroyer, model DSP1124P, a suitable processor for full range room equalization. It appears to have capability to perform this function, yet I haven't seen it being used for this purpose. If you have another suggestion, I would be interested in that too.