Home Theater Forum and Systems banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 238 Results
  1. REW Forum
    Hi, I haven't been able to discover what controls the creation of the date and time stamp on the saved graph of the RTA. When I save a spectrum measurement as a JPEG I have sometimes had the date and time added, but recently the box is greyed out and I just see "no measurement". I'm running REW...
  2. REW Forum
    Hi - I have spent a lot of time learning REW for purposes of placing and EQing my two subwoofers (SVS PB2000). I am now interested in getting a sense of how my other speakers (Totem Tribe IIs) are performing post YPAO(Yamaha 2070 receiver). The graph below shows the five speakers and the dual...
  3. REW Forum
    Here are my measurements of my two subs at the MLP. How does my room look? What should I do at this point? Any advice would be greatly appreciated. Thank you.
  4. REW Forum
    Suddenly Graph Panel is empty. Taken measurements which show up on left side. Graph panel is empty despite trying SPL & Phase, All SPL tabs. I know I am one button stroke away from activating graph panel. What am I missing. Thank you in advance, Peter
  5. REW Forum
    I'm working with multiple windows and it occurred to me that it would be handy to have a key command for 'Unselect All' or 'View Only' so that a user doesn't have to unclick (in my case) 14 windows in order to view just the one i'm interested in at the moment. It may already exist but I...
  6. REW Forum
    Hello all! I've just tried to do a measurement (my first one!). System: - MiniDSP Umik-1 mic, facing the ceiling on my sweet spot, loaded with the 90 degrees calibration file. - System: Avid HDX > HD i/o > Xmon > PSI 21M. Just measured L/R of my 5.0 system. I know i have some problems in the...
  7. REW Forum
    Hi, I have been using REW 5,16 (Windows XP) for nearly a year and have just turned my attention to the distortion graph for earlier measurements of speaker performance made with a swept sine signal. Sometimes a graph is not available, often for the first measurement in a series (on the same...
  8. REW Forum
    I cannot figure out how to print out a graph-- I've followed the other threads as best I can and ran into problem where it says - "you have already created an 800 width jpg graph in REW by clicking the Save icon in the lower left corner of the REW graph display" The problem is-- there IS NO...
  9. REW Forum
    I am using the latest MacOS REW version 5.19 beta 3 to display multiple distortion plots. When I try to switch some controls, nothing changes in the graph. This usually includes changing from per cent distortion to dB levels, sometimes changing the type of distortion, and rarely when changing...
  10. REW Forum
    Hi! I'm new to rew so maybe it is a noob question but I don't find this problem anywhere in this forum... I'm successfully doing calibration and measurement after that the graph's appearing but with only phase measurement .. nothing else even if I click on spl under the graph.. On the folder...
  11. REW Forum
    So I successfully attached a UMIK-1 mic, downloaded the calibration file and the latest beta of REW 5.17 beta 14. I set the mic to unity gain in the audio midi devices and to 48khz input. Since I am a stereo listener I just have two speakers - about 10 feet apart toed in to point to the...
  12. REW Forum
    Hi Is there any way to prevent the information contained under notes from obscuring the check boxes under the graphs? It gets a bit frustrating that the notes can at most times prevent you from checking and unchecking the tickbox. You can of course succeed eventually by messing about with the...
  13. REW Forum
    If possible, a checkbox to calculate the distortion only on the visible area of the RTA graph would be excellent. Often measuring at higher frequency rates makes it much quicker, but there's often a rise in noise above 24 or 48khz. An option to limit the distortion, THD and THD+N calculations...
  14. REW Forum
    I wanted to post my graph and ask some input. I have 3 questions and observations 1)I can't get rid of the dip at 62.7hz, not sure why? 2)What am I looking at with the big dip around 80hz? Is that the crossover, also why are there so many db's after it comes back up at 95hz? 3)I didn't have...
  15. REW Forum
    I started tuning today and this the result of some messing around. The tweeters are crossed at 2500hz 24db slope and mids 65hz 12db slope and 2500hz 24db slope The graph is full range and includes an average of all speakers Could someone offer any input on how to get a flatter...
  16. REW Forum
    It the first time I write on this forum. I wanted to ask how to read the graph with the .cal file microphone. The line of the frequency response must go to the black the .cal file? ? Can you explain how? Thank you
  17. REW Forum
    I'm looking for some EQ advise on my 3 subs, I have a marty sub and inuke 3000dsp, then 2 PA-120s. I can only manually eq the marty, I have to let Audyssey do it's thing overall.
  18. REW Forum
    Ran some measurements today, this is my front left. 90hz x-over. Can someone give me some feedback? Thanks
  19. REW Forum
    Hi! I'm new here and new in REW. I've got a problem with impulse graph. I've got some .wav files to analyse. I choose file -> import impulse response The impulse graph looks like the end of impulse is loaded before 0 -.- Originally impulse was 6sec long. I've been trying to uninstall REW...
  20. REW Forum
    Hi all, I'm new to all this, so please bear with me. (Have attached 2 x REW settings files for your reference.) I got a Mac with REW, Behringer ECM8000 and an Apogee One audio interface. I have done a measurement at my home studio and I did one for a restaurant where I recently did a sound...
1-20 of 238 Results
Top