Home Theater Forum and Systems banner

help?

  1. Rythmik plate amp (250W) specs help?

    DIY Subwoofers - General Discussion
    Anyone have any info on the specs for this amp? I can get a good deal on one, just want to see what its capable of.
  2. BFD Engine L Engine R Help?

    Electronic Processing/Equalization Devices
    Hello, I purchased a BFD off of ebay and it appears that no matter what I do, I can't seem to get the lights on Engine L or Engine R to go off, unless I am in a preset mode 7 and 9, but I guess they could be have been changed by original owner. Anyway I was under the impression that I could...
  3. Box and port help?

    Creative Sound Solutions
    Hey guys this place is great so much useful information. But I do have a few questions before I build my box. Driver is a sdx-10 with a bash 300s amp unmodified. Its a ported design using a single 4" port, length around 25-30" for a 60L box I believe was determined I need 60L to get to around...
  4. Toshiba Circuits, Is there any help?

    Toshiba
    Well finally making head way but have just one more question about the toshiba projection set. This board is badily damaged and a semiconductor has toasted the board under itself. It appears the trace is intact! Take a look and tell me if its still viable for this application. All comments are...
  5. DCX 2496 help?

    Electronic Processing/Equalization Devices
    I am using pre outs for the mains to DCX 2496, and then to ep2500, then mains + sub. I am looking for a 101 class on the crossover. This is up and operational, but not dialed in yet. Where would be a good place to start?
  6. Sub hum? Anybody help?

    DIY Repair and Maintenance
    I have a ULW 10" sub from AV123 with their factory substituted 500W plate amp. It has a low hum, particularly after many hours of standby, which may intensify when actually used for musical input. It's not the loud ground loop type hum, and all units are grounded to the same point anyway. Any...
  7. Onkyo receiver help?

    Home Theater System Recommendations
    Hello, I was dead set on getting a refurbished Onkyo 807 receiver. However, I see that the 707 is very similar, and can be purchased for about $150 less? This is for basic home theatre setup in family livingroom. Do not need excessive power, and likely only doing 5.1 setup, with maybe 2...
  8. High End RME HDSP 9632 Sound Card Gives Strange Calibration Readings; Can Anyone Help?

    SPL Meters | Mic's | Calibration | Sound Cards
    Hi all, I have two sound cards, an fairly expensive RME HDSP 9632, which is a pretty high end PCI sound card made by a German Company called RME and an inexpensive external USB Sound card, the M-Audio Fast Track Pro. With the M-Audio, I got an almost perfectlly flat response with a drop off...
  9. High End RME HDSP 9632 gives poor calibration readings; can anyone help?

    REW Forum
    Hi all, I have two sound cards, an fairly expensive RME HDSP 9632, which is a pretty high end PCI sound card made by a German Company called RME and an inexpensive external USB Sound card, the M-Audio Fast Track Pro. With the M-Audio, I got an almost perfectlly flat response with a drop off...
  10. Tang Band W8Q-1071F sealed box help?

    DIY Subwoofers - General Discussion
    I have one of these that i would like to build a small sealed box for. It will be mated to four W3-1364SA for my computer speakers. I would like some help in choosing a volume for the box. I do not have any testing equipment to determine the actual spec of the drivers. Anyone with experience...
  11. Help? Onkyo HT-RC180 issue/problem

    Home Theater Receivers | Processors | Amps
    I am fairly new to quality AVRs. I recently purchased an Onkyo HT-RC180. I hooked it up about 10 days ago. I recently calibrated it using the Audyssey setup. That seemed to go fine. I have been using it without any problems/issues for 10 days. I even used it this morning around 7am. Twelve hours...
  12. Some simple, some a little more challenging, Can you help?

    DIY Subwoofers - General Discussion
    So i am looking to overhaul my entire entertainment center, and one of my thoughts is how to go about building the TV stand. I am going to build myself a custom stand to fit just the HTPC, audio receiver, maybe a Wii, and I am thinking of tucking the Subs into the bottom of this. Currently I...
  13. Receiver Upgrade help?

    Home Theater Receivers | Processors | Amps
    Just a quick question, I have a Onkyo 605 receiver with Audyssey 2EQ. I have been thinking about getting a sub eq, like the SVS EQ1, but I really don't want to spend $700 on a eq for a $600 sub. I am adding superchunk basstraps to help smooth out the bass reponse. So instead of spending on a...
  14. New Construction Planning, Tips, Budgeting help?

    Home Theater Design and Construction
    All, Great forum. I am currently in the beginning stages of planning the finished basement with dedicated theater. As always, I am finding that compromises and creative thinking will have to be used to get the most out of my budget and space. I am going to say that I have about 10k (maybe 1 or...
  15. Newbie looking for advice...can anyone help?

    Home Audio Speakers
    Hey guys, I'm new to the home theater thing and I was wondering if anyone could help me out deciding on my first components. First, the setup is going to include a Samsung 32" 720p tv, a playstation 3 (for music, games, and blue-ray), and that's about it actually. Baby steps haha. Anyway, I am...
  16. Calibration help?

    REW Forum
    I haven't even gotten as far as calibration, so there's no telling how bad I'll get stuck when I actually measure :crying: I'm using a Presonus Firebox. Do I connect a main out (1/2) to a line in (3/4)? There are line outs that I can use, but I think the 'main outs' and 'line outs' are the same...
  17. Speaker testing in Melbourne - Who can help?

    DIY Speakers
    Hi :) Newbie here building some speakers for the first time. I am wanting to test my new speakers to determine the frequency response. Sure, I will be listening to the speakers but it's good to have some data. Look forward to hearing from fellow forum members. Happy to bring over some beer...
  18. FBQ2496 Problems need help?

    Electronic Processing/Equalization Devices
    I just received my 2496 today hooked it up as per the instructions on this forum. I took sub out rca from the receiver converted to 1/4 jack and plug it into the output on the back of 2496 marked right channel. I bought a single rca cable converted it to 1/4 jack and plugit from the right input...
  19. Waterfall help?

    REW Forum
    Just started using the rew software. I was hoping to get a little help on this waterfall graph. I am not sure exactly what I am looking at? Can I get your thought on how to read this please? I have also posted a corrected subs only graph that the waterfall came from.
  20. HTPC display issues - help?

    Computers | HTPC | Media Servers
    I'm having problems with my HTPC. When I turn it on, it works fine. If I change the input on my receiver to something else, then go back, it takes a long time for the computer screen to display again, even though I can get audio output. Sometimes it restarts, and sometimes it displays after say...
Top