Search Results for ‘hpf’

my old computer went down with all my saved data programs for my inukes 3000 and 6000dsps. That said I need help again with setting the sub paprameter to around 15hz and 18hz. I had done this previously with a + and - filter and gain adjustment but can not recall what was done. if someone can...

Hi I just got my 2X4 minidsp balanced with the 2 way 2.1 advanced plugin . just want to make sure i understand the setup for high pass filter. I select crossover, zccording to the output i have my sub connected to , for the low pass filter i select bypass, i set my HPF to 23 Hz which is the...

Good Morning I am almost done with buiding a micro marty and i need to tune the port to 23 Hz ..........I will be using a Behringer EP4000 to drive that sub so my question is what equipment do i need to add to set the HPF to 23 Hz ?? Thanks Alain

Good evening I am almost done with buiding a micro marty and i need to tune the port to 23 Hz ..........I will be using a Behringer EP4000 to drive that sub so my question is what do you recommend to set the HPF to 23 Hz ?? Thanks Alain

Looking for some ways to get around the HPF in the Behringer inukes with the DSP' s. I have the 3000' and 6000's and one want I confim my settings are correct and also other ways to go about it. I run all passive radiator setups. Here's what I did on the filter xover screen I put a high pass at...

Good evening all , I am building a new sub and need to set a hpf at 20Hz. Can i do that with the dsp1124 or Anthem ARC calibration Alain

Hi. From what I can find out, the SPA-500 has a HPF at 18hz with a Q of.707, is that correct? Can someone correct me if I am wrong. I am trying to model a Adire Audio Shiva 2 in WinISD. Thanks.

Hello people. I have finally got my sub, amp and power supply but I have an issue that I need to limit my sub for anything less than 16hz because the drivers are going beyond excursion Any idea how I would start to make one or better yet one I can buy off the shelf, ideally an adjustable HPF...

Hi In the system power section what do you enter for resistance? If I need a hpf and the amp does not have one or one that is suitable how do I add one... input, output...? Thanks in advance Mauritz

Hello, Attached is the near field measurements of my subs (Epik Legends). As you can see, there is some sort of boost at 25Hz. That is the area where the subs typically run out of juice and begin to compress. What I'd like to do is limit the bandwidth to much more manageable 40Hz and up range...

I just built two CSS Trio 12s sealed and need to add a HPF. I encountered a pop while watching Iron Man 2, which i believe is the sub reaching cone excursion. Which HPF would you guys recommend. I have the PE Bash 500s amps. I know these can be modified but not sure i want to go this route. Will...

Good morning I need a HPF that i can set at 17hz. The Reckhorn B2 hard to get so i was wondering what other option you would recommend? My sub will be a Mach5 IXL15.2.2. in a 24X24X24 vented box drive by an EP4000 and EQ with BDF1124 and audyssey Alain

Hi guys, I've completely had brain freeze this morning and need a quick question answered. I want to add my BFD into the chain with my EQ.2 and EP4000. Is it: BFD - EQ.2 - EP4000 or EQ.2 - BFD - EP4000 I am leaning towards the ealier but would appreciate a quick answer. cheers Graham

Hi all, I just build a Trio12 in a 4.5f³ enclosure tuned to 20 hz. But I'm getting bottom-out issue when I watch movie due to really low bass. So I turned the subwoofer really low for now so I don't have trouble but I'm sure that with a proper HPF I could crank this monster up a little bit and...