initial

Ok, I just received 8 2'x4' x 1-1/2" thick CertainTeed Acoustaboard Black series 300 (3 lb/cu. ft density) panels yesterday from FedEx and did some initial setup and listening last night. I didn't do any baseline measurements prior or post setup yet, so this is purely subjective listening and...

Ok, I just received 8 2'x4' x 1-1/2" thick CertainTeed Acoustaboard Black series 300 (3 lb/cu. ft density) panels yesterday from FedEx and did some initial setup and listening last night. I didn't do any baseline measurements prior or post setup yet, so this is purely subjective listening and...

I have read the help files for REW setup and am confused about which method to use for sound card compensation. I currently have the loopback setup in place (right channel meter input--left channel looped, etc.). The following quote from the help file suggests that everything is accounted for...

How do we set the initial recommended 75dB level of the AVR when using the REW?I understand that we should have the SPL meter RS or CM-140 to measure the 75dB but is this on a certain frequency initially say at 4khz just like the Rives Audio manual test CD recommended?or the REW gives a initial...

I've installed everything and am running the initial loopback calibration file in REW. I connected a 3.5 to stereo adaptor to the line input and speaker output on the back of the SB live external SC (there is no mention of line out on the back of the SB so I assume you just use the main speaker...

YouTube - Star Wars: The Force Unleashed - Launch Trailer (HD) [/CENTER]

YouTube - Star Wars: The Force Unleashed - Launch Trailer (HD) [/CENTER]

Hello, I have a Panasonic PT-53TW53 53 in. Rear Projection HDTV. Recently, the TV would not power on and flashed the service code indicating a problem with the convergence circuit. After much research on the net (mainly the great thread here by lcaillo - Thx!) I decided to tackle the repair...

I've had my dual RL-P15 IB up and running for a couple of months now. Although I haven't had a chance to run REW yet, (as I don't have the time, knowledge, or equipment right now) it sounds pretty good. Only problem is, it doesn't quite "feel" like I would have expected. Our house is tile...

Im new this forum but Ive been researching receivers on line now for a while. There are a lot of options out there in the A/V receiver market. I had been looking at the main brands in the $1000-$1300 retail price range. Onkyo, Denon, Sony, and Yamaha are the ones I had been lookng at. I had...

Hello all. Long-time lurker, first time poster. So this weekend I sat down with my Ratshack Digital SPL, RoomEQ and my BFD that's been gathering dust on a shelf since I picked it up on eBay 2 years ago. Long story short, my laptop seems to hate RoomEQ, so I fell back on the "subtest" XLS and...

Index PFG Introduction and Initial Performance Shots (Posts 1-4) Theory and Further Testing and Discussion This is a new gray made from Kilz2 and Aluminum. I say 'pigment free' because other than the pigments in Kilz2 no conventional paint tint pigments were used. For now We'll shorten it to...

Initial Impressions of the SVS PB13-Ultra compared to the (TV-12) PC-Ultra By Jon Liu I haven’t had a whole lot of time to tinker with it, since I got home kind of late and have to get up early tomorrow. But here’s what I observe from what little time I’ve been able to have with this sub so...

Hi everyone. I got REW up and running w/ ADS instant music soundcard USB and CM-140 meter (no .cal file). I took a measurement and the result is below. I believe I am doing everything ok and check levels comes back within tolerance for the input level. I am testing to 200Hz through the SPDIF of...

I recently bought a Sony KDS-55A200 55" SXRD 1080p and the Play Station 3 for a Bluray player. I had to do some setup for my system so as much as it pained me, I had both of these sitting in my second living room for the past three days without being able to play with them. I finally got my...

Sorry not using the REW software yet but planning too, so here is a initial result using the available excel version: I have some issues as you can see. This is only eq'ing my front sub which is in cabinetry (I'll get a photo up soon on that). The cabinet is eating up a lot of the sound so...