Search Results for ‘inuke’

I was wondering if I need the DSP version of the iNUKE NU1000? I can get the non-DSP version for $95 shipped w/ 3 year warranty. I don't think I can get the DSP version that cheap. So I have a Yamaha HTR-5960 which has LFE for subwoofer out and the crossover is currently set at 80hz for my...

Last night I opened up my Inuke 1000dsp to play with it. I am building a box right now, but wanted to mess around with the amp and speaker (Dayton 15" 4Ohm) before I put the speaker in the box. I have an XLR to RCA adapter for the input, so I ran the sub out from the receiver to the A input on...

Not surprised...

I have had my Behringer iNuke NU6000 for right around a year now. The loud fans have always bothered me when listening at low levels in my HT. Just last week I made an upgrade in my AV cabinet to include some more powerful fans. The result was the cabinet air temp right above the AVR runs at...

**Subs:** Dayton Audio DVC385-88 x2 **Receiver:** Denon 1913 AVR **Amp:** iNuke NU3000 non dsp I am a little confused on wiring my subs for the inuke. I assumed that I could simple connect my avr to the amp with one rca to xlr cable and then wire the subs to 2ohms and run the amp on mono...

Hi! Im planning to buy inuke nu3000(dsp) or nu6000 to power my single 12" 1500w rms subwoofer. So the question is does nu3000 give enough power? Does it give 1500w rms or what is the irl (In real life) power? If nu3000 doesnt give 1500w rms or more i have to think of buying nu6000. I dont want...

Hello folks, I've just ordered two subwoofer combos from Parts Express (18" Dayton HO driver and the knock-down 4 ft^3 enclosure). I'd like to run it with an Inuke 6000DSP. As you can probably tell, I'm very new to this. I'm clueless regarding pro-audio stuff. What confuses me is I...

I've been a home audio enthusiast for quite awhile. I just recently built my first DIY 4cu foot flat pack UM18-22 sealed sub-woofer from P.E. with an Inuke 3000dsp. Looking at all these awesome fan mods have inspired me to do my own. However I could use a bit of help. Currently I have made my...

I am using input a on the inuke. I have a Rica to 3.5 to 1/4 adapter. Bought a speakon cable and cut one end off the run speaker wire to the sub. The sub has no output at all. If I unplug the 1/4" I get a pop. I think I have no out put from the receiver or something hooked up wrong. Help...

Looking to buy iNuke 3000 DSP.

Hi everybody. I'm looking for solution to automatically power on / off inuke 1000dsp amp with the receiver? Really appreciate any suggestions. Thank you.:dontknow:

Hi, I know there are lots of inuke threads already but I was hoping someone could help me. I have an inuke powering a sunfire hrs12 subwoofer that had a faulty amp. Sunfire say the driver is 4 ohm and the amp was 1000rms. It has worked but never as well as the original amp. I have now...

O I am going to get a berry amp. Which is the better of the two amps? I, setup for regular speaker wire with binding posts but would switch.. Looked at the crest Amps and just a little too much $ for me right now .. Could get two amps for price of one.. I'm looking to go to 18's in the near...

Which is a better buy. Right now powering two 12" subs in ported box. Sold my xls1500 to upgrade to more power.. Any info is appreciated

The Ultimate Behringer iNuke NU3000DSP Fan Mod (CLICK HERE FOR PICTURES): After purchasing an iNuke, I found the stock fan far too loud for home theater use. I liked seeing what people were experimenting with here (slower fans, inline resistors to slow down the stock fan, natural...

Hi. first time subwoofer builder from new Zealand. Looking at building 2x sobotube ported (1 driver ea) or sealed (2 driver) subs using either infinity 12" 300w 1260w /or/ 15" 350w jbl gto1514 subs with an inuke 1000/3000dsp. Will i need a cleanbox to boost the signal from the avr subout to...

I just got a Inuke 3000 DSP from Samash.com. Got it for $229 shipped. They had a sale where if you spend $300 they would give you $50 off. I had to get the deal through live chat with an agent. This is the best deal i found on the INUKEs since their price is the same everywhere.

I am a noob that is just completing the builds. I have the following config. 2 Woofers in independent sealed boxes that will be bang on 4.0 cubic feet each internally Woofers are SI HT 18 D4's Amp is iNuke 6000dsp I was planning on running @ 4 Ohm on each channel with the limiter set. Prior...

I am almost finished my home theater!!! Finally!! I am looking to buy an amp to power 4 15" Dayton Ultimax in a sealed box. I am currently looking at 3 amps and wondering the follow: iNuke 3000 QSC PLX 3402 Crown XTi 4000 Is the QSC PLX3402 or Crown XTi 4000 amp a good amp for driving...

Greetings all, Like so many I tested the iNuke waters a few years back with a 1000DSP. That was my first Class D amp, still shock at how well they work! But I wanted to upgrade the overworked iNuke 1000DSP so I looked all the way up to the iNuke12000DSP. I like the iNuke amps but not the...