Home Theater Forum and Systems banner
inuke
21-40 of 60 Results
  1. Home Theater Receivers | Processors | Amps
    Hi team! I just completed a ported sub for my music group, using an Eminence Kappalite 3015LF driver. It sounds great, but I need some guidance in setting the LP filter. The sub is designed to provide LF extension to a pair of Bose L1 Compact speakers (F3=65 Hz).The iNuke offers the following...
  2. Subwoofer Amps | High Pass Filters
    Hi, searched quite a bit but seems I can find solid info on how to wire these.. Given how many people seem to ask the same question one of you:) more experienced types should post a sticky.. I did a quick line diagram and this is my first attempt at pro gear so hopefully it works out. Could...
  3. Subwoofer Amps | High Pass Filters
    $25-shipped for a 2-pack of Noctua 80mm fans. I went from 77dB to 50dB. I even forgot to add the inline resistors to slow the fans down. But there's no point. The amp is almost silent as-is. But I can still add the resistors if I feel the need w/o any cutting or soldering. I don't have my subs...
  4. Sealed Subwoofer Build Projects
    I built my first DIY sub. A Dayton 15" Ultimax (dual voice coil) I connected it in series. I believe this makes it 4 ohms correct. I connected the terminal ends to opposite ends of the woofer then connected a single wire from the other + to -. (Could I have just connected one side to the...
  5. Subwoofer Amps | High Pass Filters
    So I am about 99% dialed into a "MartyCube" build using a Dayton 460HO 18" driver with a iNuke 3000 DSP. The iNuke will be bridged and set to give a max of 1100 watts to the Dayton. Here is my question. I see some differing info on what the stock fan's voltage is on the iNuke. I plan to...
  6. Subwoofer Amps | High Pass Filters
    Sorry for the simple questions but I'm interested in an inuke 3000dsp to power two subs. My AVR only has one RCA sub out. I downloaded the DSP software and it looks like I can put it into bridge mode. If I do that, would I have to splitting the sub out from the AVR and attach 2 sets of cables to...
  7. Subwoofer Amps | High Pass Filters
    Ive never used a pa amp before. I was wanting to know how to wire one for use on a reciever and power 2 subwoofers. I read the specs of the inuke3000 but im not sure if you only use ch2 for low end and not use ch1 cause thats where full range is? Just a basic how to hook up to reciever sub out n...
  8. Sealed Subwoofer Build Projects
    The behemoth B&C 21" is on the burn-in (now 6 hours) and I can't wait to stuff it into the cabinet on Sunday. Got the UMIK, REW and the Nuke all ready to go. I still have to decide on if I want to do the dual-sealed, which means another $700...these drivers just don't fall in price. At least not...
  9. Subwoofer Amps | High Pass Filters
    Crown XLS vs Behringer iNuke - A mostly subjective comparison. Background: Last Spring I was building a sub comprised of one of Erich’s 3cuft flat packs and the newly released Dayton Audio UM15-22 and as part of the build I needed to buy an amplifier. I wanted a stand-alone amplifier, because...
  10. Subwoofer Amps | High Pass Filters
    i just picked up a 3000DSP and am planning two sealed 15's or a single dual opposed box. My first build ever sans the decware 10" deathbox i built for my car in 1993. Can you help me find some information like "dsp for dummies" that i can read? From what i've been reading so far on here and...
  11. DIY Subwoofers - General Discussion
    I put together an Ultimax 15 on a sealed box with an inuke 1000dsp and I having a little bit of an issue getting any output from the sub. I have tested the sub out of the box wired with the voice coil in series and a 4 pole neutrik connectors with the following configuration using 12ga speaker...
  12. Subwoofer Amps | High Pass Filters
    I hope the iNuke 12000dsp is released this year. It would be best for me if it was 6000 peak at 4 ohm and around 4000 music mrwv (music real world volts). I would like to power 2 big subs, one off each channel. I am loving my 3000dsp after changing the fan. The DSP is very easy to use. I...
  13. Subwoofer Amps | High Pass Filters
    Hello everyone I'm trying to build my HT system and now I'm designing the sub-woofer system (I have another thread for the driver and the enclosure). My first option was a Yung SD500 amp plate. I liked this because it is a class D amp, it has variable phase and looks nice. But after...
  14. Subwoofer Amps | High Pass Filters
    Just a casual observance while I've been tuning using REW. The subwoofer is a sealed unit made by ADS, model SW5, that I fixed up to use while working on my own DIY Shiva X. When I hook up my Dayton SA240 (240W plate amp.) the little ADS comes alive with a great rumble with the gain knob...
  15. Home Theater Receivers | Processors | Amps
    I need a little help. I have a Behringer iNuke 6000 that does not have the remote on option. To remedy this, I plugged it into a "Switched" outlet on my power conditioner. When the AVR is turned on, it triggers the remote outlets to come on. I have to leave the iNuke on all the time, but it...
  16. Home Audio Subwoofers
    Has anyone used passive versions of the JTR Captivator with the iNuke 6000DSP amplifier? Any reason that amplifier wouldn't be a good choice to run a pair?
  17. Subwoofer Amps | High Pass Filters
    Hi all, Been awhile since i have posted. I was just about to pull the trigger on purchasing a NU6000DSP and I went to Behringer's website to read up more on the NU6000DSP vs NU6000 to see if i really needed to spend the extra money for the DSP. Now i see that Behringer has an NU12000 coming down...
  18. Classifieds - Wanted
    My DIY project looks like its going to cost me more then I planned and if anyone has one laying around I would love to scoop it up. Thanks in advance
  19. Subwoofer Amps | High Pass Filters
    Hi guys, I have my Inuke 6000DSP now and just realised that it only has neutrik speakon connections. I was running single speaker bare wire into the ep4000 to rca on the speaker plate on the sub. Can you get a single neutron to rca cable and if not what do I need. It would be a pain if I...
  20. Subwoofer Amps | High Pass Filters
    Hi Im looking at spending some cash to buy an amp to drive a future driver i haven't decided on. Im thinking a single 15". I found this amp the Behringer inuke NU3000DSP and thinking of running this at 4ohms bridged. Im looking at spec and it almost seems to good for the price. Has anyone...
21-40 of 60 Results
Top