Home Theater Forum and Systems banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-11 of 11 Results
  1. Home Audio Acoustics
    Hello, to all. I know from HT practical installations, that it is very important to get right acoustical dimensions for acoustical projecting. This means, that, in particular, ears resolution for low frequencies (20 - 200 Hz) must be taken into consideration to avoid negative resonanсes...
  2. DIY Subwoofers - General Discussion
    Hello, I am fairly new to the home theater scene - see thread here: http://www.hometheatershack.com/forums/diy-subwoofers-general-discussion/151905-new-diy-need-advice-driver.html - but intend on going "all out"!! A quick run down of my current set-up: Yamaha A3060 Receiver 2x Crown XLS 1502...
  3. REW Forum
    After hearing about room calibration, I decided to give it a shot, but it seems I'm stuck on the sound card calibration part. For reference, I have a UCA202 DAC/ADC as well as a Motherboard Line-in port. The UCA202 mic input has a noise floor of -60dBFS, while the Mobo is lower, at -85dBFS...
  4. REW Forum
    Hello, I am using two Klipsch Epic CF3 in a treated room (absorbers in the corners, ceiling and the side walls) and two Klipsch THX KW120 subwoofers. The integration of sub and mains (80Hz double bass for stereo and 60Hz sub alone for HT) is good and I love it with both 2Ch and HT. I am using...
  5. New Member Introductions
    Hello everybody, I'm Dimas From Argentina and want to get some response from a Bass Reflex that I've designed I'm planing to use Room EQ Wizard and a ECM8000 Mic. Do you have any suggestions like :coocoo: Uooooou You need another mic or yes!!!!:clap: it's OK !!! go on !!!! Thank you !!!!!!
  6. Home Audio Acoustics
    Recently I did acoustical measurements at new recordings studio in Astana (town – capital of Kazakhstan). Unfortunately, there were not any architectural documents, but it was need to know the height of the room. There was not any stairway, the height was too high to use a chair or table. After...
  7. Home Audio Acoustics
    Dark Blue line is front row Blue/Green is rear row. 2 SUBS. I moved them around the whole room and measured, looking for the location with the least dips in response. Adjusting phase and re-measuring. This is 0 treatments, 0 eq. The 2nd graph shows all the measures as a cobbled mess.
  8. REW Forum
    Hello, I am playing with a newly bought Galaxy meter that was calibrated down to 5Hz. However the results I am getting at the extreme LF do not look realistic at all. As you can see in the attached REW measurement snapshot I am getting a 30dB jump between 15Hz and 5Hz. Is it even...
  9. Subwoofer Amps | High Pass Filters
    I am in a build project for a stereo pair of 450L enclosures with 2 each TC Audio LMS-R 15" in each, ported low with individual cabinet space for each driver. I have 4 SPA-1000's that will drive it but I seem to be running in to a Low end role off at 18Hz. The cabinets should give me good...
  10. DIY Repair and Maintenance
    Hey guys. A friend has a pair of Cerwin Vega VS 100's and has foam rot along the bottom of the speaker. I have never done a repair on one of these but I am very good at fixing anything that requires attention to detail. He wants a repair kit in red to keep the traditional look of the CW...
  11. REW Forum
    I've run into an weird issue with REW. When I measure the sweep in REW, I can view the LF Waterfall no problem. However, if I save the measurement, exit REW, open REW, and load the previously saved measurement, LF Waterfall does not work. It only shows a blank graph. Am I doing something wrong?
1-11 of 11 Results