Search Results for ‘main’

I'm finally unpacked... ]

Hello Everyone - I'm new to these forums and looking for some suggestions. I recently ran speaker wire to my dining room and I'm looking for an Wall mount speaker. Since it's a dining room I would prefer it to be low profile. The room is about 12' x 15' Thank you in advance.

Hi, When i start REW on Mountain Lion it start always with a minimized window ( very small), hard to find it in the desktop. What can i do to start it in full size? Thanks.

I have a weird problem here. I have Martinlogan Electromotion mains. When I run them in any mode other than stereo direct analog or pcm they are fine. When place in stereodirect the left one is 10 db lower. It does not do this when I run multi channel direct. I have swapped all cables around...

Ok, so I am settled on where I will layout my home theater in our open floorplan basement. See the layout below: Currently, I have my first row at around 14' (to viewer's head) from the screen. The room is 28' long and at the 14' mark, I have room for a 2nd row on a riser, and a 3rd row...

I am swimming in PDF literature, trying to understand basic zone functions before purchase of a new a/v receiver. The budget is $1500 +/-, and I've researched Pioneer Elite SC-7*, Yamaha Aventage, Denon X4000, and a few Marantz models. But stumped is me. With the risk of being too vague, I would...

Hello, I am using two Klipsch Epic CF3 in a treated room (absorbers in the corners, ceiling and the side walls) and two Klipsch THX KW120 subwoofers. The integration of sub and mains (80Hz double bass for stereo and 60Hz sub alone for HT) is good and I love it with both 2Ch and HT. I am using...

Hi I have recently brought a calibrated Mic and measured my room which has the mains and sub EQ with a Tag Mclaren processor. Both of the measurements are averages of three positions across the listening position. I would appreciate any feedback please?

I have a Toshiba 65H82 which started getting wavy when cold. This progressed until the image was not viewable. There was an image, just too distorted to watch. BACKGROUND With some searching, I found the Hyper Board was a likely source of the problem. I removed the board and sent to an eBay...

Hi guys, first off I wanna thank the people at HTS, REW, Cross Spectrum labs for being such an influence on my life wrt critical listening. I'm about a day or two out from the cutoff date to return my dbx231s to GC I was certain that I was gonna go replace it with a DEQ2496, but as I'm...

I have an Onkyo tx-nr616. I am trying to send an audio signal to a power amp for the rest of the house. The onkyo will not link the volume of zone 2 to the main volume and it will continue to play another input after the main input has changed. This amp is disappointing. The hdmi out to the tv...

I have an Onkyo tx-nr616. I am trying to send an audio signal to a power amp for the rest of the house. The onkyo will not link the volume of zone 2 to the main volume and it will continue to play another input after the main input has changed. It will even continue after the amp appears to be...

Looking to upgrade my current front main speakers. Over the past few months I've built a few DIY subs and all completely overpower my current mains all be it not a hard thing to do as they are paradigm mini monitors. So I am looking at doing a kit or DIY front stage that will supply me with...

I have a Hitachi 53UWX10BA which I got used. The previous owner said "when we turn it on, sometimes there is no picture but other times there is a picture. When it comes on, it looks great." I took it home and see two problems. 1. The convergence needs to be adjusted. I assume it could be out...

Hi What is the best tool to use for setting distance for main speakers. Also the process please. If i EQ, does the distance setting change?

I have had this L32WD12 laying around for quit awhile now and finally found the board I was needing. The old board would tweak out when connected HDMI, so I took the TV apart and found that the board was covered in electronic blood as I would call it. Something popped, couldn't really tell what...

My main system The chain Denon 2808 6 channel HT amp with chan 6 ded to 2 channel Carver M-1.0t MKII op2 amp for 2 channel with 99% silver IC OppoBD83 SE HDMI IC to Denon Sony CDP CX355 opt IC to Denon Verizon Fiber Optic TVR HDMI IC to Denon Samsung 54" Plasma 1080IP 240Hz HDMI IC to Denon...

Epson 8700UB projector Draper 92" Cineperm 1.2 gain B&W CM1, CMC speakers SVS SB13-Plus Velodyne SMS-1 Sony BDP-350 Bluray Onkyo 875 receiver AKG K701 headphones