Home Theater Forum and Systems banner

measurement

  1. REW Forum
    Hi, I am trying to take measurements with REW and I'm using a Sound Blaster MP3+ USB powered sound card. But - when I take the measurements, the audio cuts in and out and the result is a screwed up measurement. Like 10% of the time I get a measurement where the sound doesn't ever cut out at...
  2. REW Forum
    This was a measurement of my JL F113. It doesn't look good to me, your feedback?
  3. REW Forum
    I finally got REW set-up on a laptop, using a Behringer ECM8000 (didn't use Sonnie's calibration file) with a Behringer Xenyx 802. On the Xenyx, I set EQ for high, mid, and low to be zero (at the 12 o'clock position), the FX to negative infinity, and level at zero. Is this correct? I used the...
  4. REW Forum
    I finally calibrated everything. I tried my first measure, and here is the graph I get ??? What is wrong ? Thank's for your time guys Chris
  5. REW Forum
    First let me apologize if my graph is not formatted correctly in regards to the db levels (but that me be my issue). I went through the help files and believe I have calibrated the sound card and SPL meter correctly. I loaded the digital cal file for my RS meter. I ran the output of my soundcard...
  6. REW Forum
    i took several measurements... one for each crossover point 80,100,120, with the subs alone and with the subs+main... then i also did it with the subs+main and the l/r speakers set to large... so i was just wondering what u think of and make of my results... here are the first results of the sub...
  7. REW Forum
    My first question is about the smoothing adjustment on the Filter Adjustment tab. What smoothing adjustment is recommended? Second question is a bit harder to ask. I'm passing the REW signal to the multi-chanel sub input on my receiver (Pioneer Elite 56Txi). I have an IB sub with no...
  8. REW Forum
    Hi, again i would like to thank everyone for all your help getting me up and running. I think this program is great. I have been testing and moving my speakers around to try and improve my results.( speaker placement makes a huge difference. Even moving as little as a few inches)I am currently...
  9. REW Forum
    Hello! My new dedicated HT is so close to being finished I can hardly stand it. Four months in the making! I have started calibration and have taken some initial measurements using REW and I am pretty pleased with the results. The bass traps must be working! (Here is where I would input the...
  10. REW Forum
    I have been equalizing my subs with REW over the last couple of days. One thing I am unclear on and have been unable to find in the help file is how to go about re-testing the sub after filters have been applied. I started by testing the un eq'd sub, I then applied the auto filters, and tweaked...
  11. REW Forum
    can rew or a similar program show responce from an external sweep? Just wondering as i have an lp with a 20-20000hz sweep, be interesting to see what it looks like. edd
  12. REW Forum
    Hello, Sorry about the thread title. It should read Finally have BFD and made my first measurement. Ok I made a measurement of my PB12-Plus and have attached the graph. Where to start? What do you guys think? Any advice? Does the dip at 45 look too bad for the BDF to take care of? Thanks...
  13. REW Forum
    First try of studio monitor in my small room. 11x17. Event ASP6. Any thoughts on tuning my measureing is appreciated.
  14. REW Forum
    First try of studio monitor in my small room. 11x17. Event ASP6. Any thoughts on tuning my measureing is appreciated.
  15. REW Forum
    Okay... it's a holiday here and I was somewhat bored... so I decided to do a measurement test. I often wondered when we do our measurement testing for our subs and we place the mic at the location that we believe is center of our ears is really accurate enough. After all, our body is not there...
  16. REW Forum
    I thought I'd try something today. I used REW to measure my sub using the RS meter technique outlined in the REW help files, then I did it again using a Behringer Calibration mic and a studio-grade mic preamp. The constants were the computer, the soundcard (external Creative USB), the measurment...
  17. REW Forum
    I thought I'd try something today. I used REW to measure my sub using the RS meter technique outlined in the REW help files, then I did it again using a Behringer Calibration mic and a studio-grade mic preamp. The constants were the computer, the soundcard (external Creative USB), the measurment...
Top