mkii

I am having a hell of a time getting my UR22 mkII setup with REW. Looking for suggestions. Equipment: Steinberg UR22 mkII, Dayton EMM-6, Asus Laptop, Yamaha AVR. My issues start right at the beginning with the soundcard calibration. I have my UR22 hooked up with input 2(R) looped to line out...

Hello guys I'm very much a noob when it comes to home theatre systems. I've narrowed my 5.1 speaker system search to the above 2. Considering that the Bose Acoustimass 6 III would cost about 2 times the price of Boston Acoustics SoundWare XS 5.1 SE MKII, I like to hear what you guys think when...

Hello to all, I would like to buy an amp (integrated or power) for my speakers but not really sure. I dont want to under power them but I also don't want to spend unnecessary money. Please help Specs on my speakers 3-driver, 2-way bass reflex. Quasi-3rd order resistive port CROSSOVER: 3nd...

I am using Tascam US-144 MKII. I have successfully calibrated the sound card with the loopback connection. I have the following questions: 1) At REW's Sound Card Calibration page, I tired to lower the level with the "Control output mixer/volume box" in REW, but it is grey out! How can I turn...

Looking at 150 litres tuned to 22hz. Single circular 150mm port, about 620mm long. I know it's on the small side for this driver, but WAF is at its limit. Also port velocity gets high when up around the full 700 watts I have to feed it with, but it will seldom run at full tit so I'm not too...

Why do so many audio products have the letters "MKII" in their name? I see it everywhere. Its like that movie "23" but with audio products.:huh: or am I :coocoo:

I have read many posts on using the US122/144 with REW and I don't know if it's because I'm using a pre-MkII unit or I'm doing something wrong, but I can only use it at 44.1. I can use other apps with it at 48, but when I start REW (even if it had been set to 48 the last time it was shut down)...

Hello I tried to calibrate brand new US-144 soundcard for my friend. We connected a cable from output RCA socket into mic XLR input, and disabled the Phantom power I followed the instructions on screen (to match the levels of input and output), however no matter what I did, REW reported on 7db...

I m going to use the Tascam 122 MKII with REW (+cross spectrum ECM8000). Can someone tell me step-by-step what I need to do for the Tascam to get it working correct with REW. The hardware (cabling) setup is already done: ECM8000 is connected to xlr R input of the Tascam and rca R output of the...

Please help me decide between these two, especially if you have tried both. I'll be using it on a Win7 64bits laptop with a calibrated mic. Here's what is important for me: 1) No issues / easy-to-use with REW 2) Measurement accuracy 3) Sound quality / DAC quality - since it may replace my...

Hi Shacksters, Happy Thanksgiving to all. I am contemplating a new front speaker purchase (LFR) and am trying to see if anyone here has had any knowledge or use of the SEAS Loki MKII coaxial kit from Madisound? It uses a SEAS 7" coaxial driver in a front ported box, which would be perfect for...

Can I use an M-Audio Fast Track MKII (alias Avid studio recording) for impedance measurements. It only have one mono input plug. Is thre any way to connect it with REW? I know it required 2 channel input for this measurements. Excuse me for my english. Thanks.

I tried for days now but not get any decent graph anymore out of REW. It was working in the beginning but after another week I wanted to test again and have problems since. What I noticed is that after calibrating the SPL in REW it will not fall down from 75dB to lets say 50dB. When...

Does anyone know what is the difference between Avid's M-Audio Fast Track and the Fast Track MKII? Is it just an updated model? Is the Fast Track obsolete? Are there any feature or performance differences between the two models?

I have been looking at a Carver M 10t with the MKII upgrade. Has anyone had any experience with this amp? Will be driving a pair of B&W 705s 2 channel only for music with a Denon 2808 for the pre. Thanks as always

I really just want one, but if it takes a pair, let me know. Thanks.

Looking for a pair of Contour 1.8 MK II and a pair of Contour 1.3 MK II. Black color is preferred but not important. Know of any possible leads? Please send email to: nelsondog at shaw.ca Thanks for looking!

I just upgraded from my Yamaha RX-Z9 to the Denon AVR-5805 MkII. I have it hooked up, but I have not been able ot put it through the test. First impression is that the Yamaha GUI is far superior, but the Denon is much more flexible to set-up. I'll report back on the sound differences.

Upgrading so these have to go first: 1. ***SOLD***Bob Carver Sunfire True Subwoofer Mark II $575 shipped in the continental US. This is is perfect working condition and was just checked by Sunfire a couple of months ago. There is some very minor surface wear (scratches). Pictures available...

I just got a BFD 1124P and was wondering if it would be difficult to integrate a mid-bass module. From reading on this forum, the idea doesn’t appear to be that popular. There are a lot of positive feedbacks over on the HSU forum. Individuals who’ve tried it seem to have been blown away...