Home Theater Forum and Systems banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 342 Results
  1. DIY Speakers
    iv got a question an i hope you can help im planin to build some bookshelf speakers that have 2 8in woofers an a planar tweeter in a two way config using the Dayton Audio 700-LPF-8 Low Pass an Dayton Audio 700-HPF-8 High Pass but my problem is i cant see how to do that , i know it should be...
  2. REW Forum
    Finally got REW setup and went through my first test. MDAT file attached here for those who wish to comment! Regards, Dan
  3. Home Theater System Recommendations
    Hello, I'm after a bit of advice on buying a new home theater system. My knowledge is fairly basic on the subject, so please excuse any incorrect technical terms etc below! Excluding the Bluray player which I will sort out later, I'm after advice on which make / model amplifier to go with, and...
  4. Audio Processing
    i have an issue iv been trying to find a 4K at 60hz with 7.1 HDMI Audio Extractor that can pull dts 5.1,dolby 5.1,lpcm 2 an 5.1 7.1 audio while allowing 4k at 60hz with yuv 4.2.2 12bit rec2020 from nvidia sheild an connected to a VIZIO SmartCast™ M-Series™ 55" Class Ultra HD HDR XLED...
  5. REW Forum
    I'm trying to measure a pair of new Goldwood drivers I received for Christmas that I plan to use for outdoor speakers. I'm following the instructions provided online. The calibration worked just fine. I'm using a USB Soundblaster XFi soundcard switched to headphone out. I have a 100 ohm...
  6. AV Home Theater
    im rebuilding my home theater system an im try to pick my centers fronts sides an backs and i'm looking for something that can take a rms 200watts per channel an is at least 30hz to 30khz at minimum Sensitivity: 92dB i have 4 Crown XLi800 one to power each set an im running a Crown XLi1500...
  7. System Setup and Connection
    I am having a new theatre room built, and I want to have it wired for Atmos support as well as (7.1? 9.1? Not sure which is the one really) The room is 20ft 6in long X 14ft 8in wide with 9ft ceilings and two rows of seating (the back row on a 8in raised platform.) See pictures below for a...
  8. System Setup and Connection
    Hi - Just bought a new house that came pre-wired. The pre-wiring plate looks like this...
  9. DIY Repair and Maintenance
    I have a VPL PX15 - I recently replaced the lamp - while I was doing this I blew out the whole chassis because there was 15 years of dust everywhere. When I fired it back up there were globs of dust spots in the picture - mostly visible on a white background. Thinking this was dust spots I took...
  10. Home Theater Design and Construction
    I am in the planning stages for some home theater goodness in my currently unfinished basement. I need to get this baby pre-wired and am struggling a bit with some speaker placement. The room is not really ideal. In the diagram below I have it layout out for 7.1.4 (sub location isn't on here...
  11. REW Forum
    Hi! Sophomore REW user here regarding "Calibrating the SPL Reading" section of REW Help. I came across a thread that made me a little nervous about entering a value accurate to one significant decimal place. So I have a couple of questions: How important is it to enter a precise value into...
  12. System Setup and Connection
    guys, need help... I've decided to install ATMOS in my HT and wanted to take the chance to reconfigure my HT. But I'm kind of stuck cos I'm not too experienced in overhead and height configs to optimise the immersive sound. :-\ My limitations are: - my couch is against the wall, and that...
  13. REW Forum
    I calibrated the RME BabyFace Pro sending on Ch1 input a logarithmic sweep (volume: -12dB) generated via Room Eq Wizard at the BF PRO output (loopback sweep). I experiment instabilities (+1.4 dB to -43 dB for 20 Hz to 20 kHz) for a buffer size of 32K (sample rate: 48 KHz). The mic input is not...
  14. Home Theater Receivers | Processors | Amps
    Hello, I have an Onkyo TX-NR636. I am looking for suggestions on adding an amplifier to increase was audio quality. I just bought a second subwoofer(Klipsch R-10SW - Yet to be installed) - I realize I need to buy a new receiver at some point. I have Dolby Set-up, below is a list of my current...
  15. REW Forum
    Hi all. I'll try to keep a very long story short! Basically, I have a DIY subwoofer: two drivers (Acoustic elegance av12's) mounted in a push pull configuration, sealed box. Powered by Behringer EP4000 power amp. I have recently upgraded a couple of items, namely, speakers to Monitor Audio...
  16. Home Theater Design and Construction
    Hello, I'm currently in the planning stages of a theater and would appreciate any input that you might have in regards to the following design. The max width I have is around 10' and the max length I can see using would be 14'. Ceiling height is about 7' 2.5". The particular layout attached...
  17. New Member Introductions
    I have been a Dj for a while now, and over the years have gradually upgraded my system to now be limited by the rooms I play in. Over the last year I have settled at one location and virtually installed my system in the club. I now run sound for live bands and want to continue my learning but I...
  18. General Service and Technical Information
    Hi everyone. I hope I have this thread in the correct section. I have a velodyne CT-150 that has always been a trooper and served great throughout the years. But a few weeks back after some cocktails and cranking the volume a little too much, the factory plate amp finally gave up. I am using...
  19. REW Forum
    Hi All I want to use REW to EQ the two SVS PC-13 Ultra subwoofers that I have in my home theater. I had the room professionally calibrated a few years ago, but I recently replaced my Integra pre-pro with the Maranzt 8802A and decided that I would try REW to smooth out my bass response. I've...
1-19 of 342 Results
Top