Home Theater Forum and Systems banner

ohm

  1. ?? about the 15" TXX-BD 2 Ohm DVC Subwoofer

    DIY Subwoofers - General Discussion
    does anyone know what the watt rms per coil is on the audiopipe 15" TXX-BD Series 2800W 2 Ohm DVC Subwoofer im tring to find out if one per channel can be powered by a the crown 1502 which puts out 550watts at 4ohms an 775 at 2ohms im tring to deside if i want to run as a 4ohms 2 channell amp...
  2. Ohm load of speakers in series?

    Home Audio Speakers
    A pair of 8 ohm speakers, and a pair of 4 ohm speakers are wired in series. What is the ohm load felt by the amplifier? I know that two 8 ohm speakers in series would be 4 ohm.
  3. Tower speakers DB717TL 4.5 ohm

    DIY Speakers
    Hey bros I just picked up a pair of transmission line Dave Brown design 717. Which are two tower speakers vented in the back up top with 2 mid woofers Dayton rs180-8 8 ohms that are ran in series with a 4 ohm dome Dayton tweeter . The speakers come in at 4.5 ohms when I checked them . My...
  4. mixing 8 and 4 ohm speakers

    System Setup and Connection
    I currently have a 7 channel Polk Audio LSI setup powered by a sunfire TGA 7201. I have been drooling over the new lsim and have ordered a pair of 705's and 706c in cherry. My rear surrounds are the lsifx bi-pole/di-pole and I absolutely love them, an upgrade will be in the future but funds and...
  5. 4 ohm bridged or 8 ohm "stereo"

    DIY Subwoofers - General Discussion
    Hi all, I am working on an infinite baffle setup with the Behringer EP4000 and 4 FI-IB3 18" sub woofers. The subs are 4 ohm single voice coil. The original plan was to run them bridged at 4 ohms. I know that is technically overkill, but then I got to thinking about running them at 8-ohms by...
  6. 3 ohm reciever to 8 ohm powered subwoofer

    System Setup and Connection
    I have a Samsung surround system that has 3ohms and just purchased a Polk powered subwoofer (8ohms). could this damage the subwoofer at all and if so is there a way to protect it. I really don't care too much about the Samsung receiver as I am looking to upgrade that in the next month or two...
  7. Amp to speaker ohm difference?

    General Service and Technical Information
    I recently picked up a pair of MTX P215H speakers, 4ohm 300 watt RMS 1200 watt total power frequency response 36hz-20khz. My amp\receiver is a Pioneer Elite VSX 70, the manual says the unit supports speakers with a nominal impedance of 6 to 16 ohms. My question is will it hurt or effect my...
  8. ohm question

    Home Audio Subwoofers
    Ok to start I have a Advent ASW1200 powered sub that the speaker is blown. Its a 12" 4ohm sub. My question is I have a Peavy 12" 8ohm speaker I would like to put in the sub box, can it be done with the different ohms? What will happen if I do use it? Thank you
  9. 32, 250 or 600 ohm headphones.

    Headphones | Head Gear
    Can one tell the a difference in audio quality between headphones with different ohm specs. Such as the Beyerdynamics 880 or 990 that you can get with different ohms... Just getting into this headphone stuff ...
  10. bets are on! inuke 12000. 2 ohm or 4?

    Subwoofer Amps | High Pass Filters
    I hope the iNuke 12000dsp is released this year. It would be best for me if it was 6000 peak at 4 ohm and around 4000 music mrwv (music real world volts). I would like to power 2 big subs, one off each channel. I am loving my 3000dsp after changing the fan. The DSP is very easy to use. I...
  11. Yamaha Aventage Line, good for 4 ohm speakers ??

    Home Theater Receivers | Processors | Amps
    Are the new Yamaha Aventage AV recievers like the 1020 or 1030 good to drive 4 ohm speakers ??
  12. Looking for a LCR project

    DIY Speakers
    This system will be a home theater workhorse and I will require something that can keep up with a single SI-18 HT subwoofer fed with 300W plate amp for now, upgrading to a crown or behringer amp and minidsp for EQ as funds allow. The room is half of a basement which is closed off with a door...
  13. Re: RE Audio SR15 Dual 2 ohm

    DIY Subwoofers - General Discussion
    Re: RE Audio SR15 Dual 2 ohm Hi Guys, Just wondering if anyone has had any dealings with these drivers. I can get them for £94.90 each so probably a discount to be had for 8. I have modelled 8 in a sealed box of 24 cu ft so 6 cu ft for each dual. They come out at 108.5db at 10hz and 121db at...
  14. Behringer A500, can it really do 600W into 8 Ohm bridged?

    Subwoofer Amps | High Pass Filters
    What is the actual RMS I can expect from a bridged A500? I am skeptical of the 600W claim but had any body here ever measured it? I have a spare A500 and I was hoping to use it with CHT 18.1 sub (8 Ohm, 18" driver, sealed ) until I can afford a better amp. Is it worth a try? thank you
  15. Looking for amp capable of 1 ohm......

    Classifieds - Wanted
    Hey I have two custom built subs.. both are dual 4ohm vc. I can also wire these to be 2 or 8 ohm per sub.. I need something to run one for now and two later on.. . I have a onkyo receiver and a elemental designs eq.2 so far.. looking to stay around 300 max plus pay for shipping.. email is...
  16. Using 8 ohm speakers with a HTIB 3 ohm receiver

    System Setup and Connection
    I just purchased a pair of Polk Rti 4 bookshelf speakers I'd like to use as my fronts, but I currently don't have a good dedicated AV reciever to use them with. I do have an LG LHB 306 HTIB reciever which reportedly uses 3 ohm speakers and 141 watts to each of those speakers. What I'm wondering...
  17. 6 ohm center channel

    Home Theater System Recommendations
    Any reccomendations on a solid 6 ohm center channel? I want to replace my center and all 4 of my hts speakers are 6 ohm's ... any experiences / reccomendations? Thanks!!:help:
  18. wiring options for dual voice coil woofers

    Sealed Subwoofer Build Projects
    So I am looking at some ed 18's for a dual oppossed design. They come in dual 2 ohm voice coil. Ed emailed me and told me that if I bought them, the only wiring options available to me would leave me at either 2 ohm per cab or eight. Now the question I am asking is... Couldn't I wire one...
  19. Bogen 70V/4, 8, 16 Ohm mixer-amps

    Classifieds - Pro Audio
    I have many used Bogen C60 (60 watt) and C35 (35 watt) 70 volt/4, 8, 16 ohm (switchable) mixer/amplifiers for sale. These were used in a permanent airport installation to distribute audio over 70 volt lines to multiple speakers. All are in perfect working order and, except for some light...
  20. Building a Dayton 15" classic 4 ohm, sealed

    DIY Subwoofers - General Discussion
    This is my first post on HTS. I will be running the dayton 15" classic 4 ohm driver with the Dayton 240w plate amplifier off the line in from my ep1500. I would prefer a sealed box. I will probably use birch plywood because I hate cutting mdf. The T/S parameters are as follows: Power...
Top