Home Theater Forum and Systems banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 500 Results
  1. Official DVD and Blu-ray Reviews
    I have a Onkyo TX nr1010 and just ran the Audyssey MultEQ XT32: Auto Setup set up for 5.2 surround. The on screen message says to lower the dbs by 4.5 when 2 subs are used. Question is why. Also can I set the level at the beginning of the set up to 70.5 instead of 75.
  2. Home Theater System Recommendations
    Hi all, My receiver (Onkyo HT-R391) has sadly decided to stop working recently. A mate of mine has these two receivers (Onkyo TX-SR507 & Denon AVR-1803) lying around until I can properly upgrade the receiver. Just wondering your thoughts on these two and which I should go with? Or even if it's...
  3. DIY Repair and Maintenance
    Hi Folks Not entirely sure what's happened but i'm now the proud owner of large brick rather than an Onkyo AV Receiver; hope someone can help. After switching inputs last week, the receiver went 'strange' and then, without me resetting it, started to click on into standby and then instantly...
  4. Home Theater Receivers | Processors | Amps
    Hello, I'm a new member here at the shack and am looking to upgrade my older Yamaha RX-V750. I've been doing a lot of research an several forums and think I want to go with either an Onkyo 805 or 705. I've been reading that the 06 models are not as good as the 05 models but the problem is, I'm...
  5. Remotes | Cables | Accessories | Tweaks
    Hello Experts, I am looking for a USB bluetooth device to be used with HT-R391 AVR. I looked online on Onkyo site and found 2 devices UBT1 and UWF1 and am not sure if these are compatible with my AVR. The compatibility list that they mention is starting from a certain model but doesn't clearly...
  6. Home Theater Receivers | Processors | Amps
    I may be replacing my old but trusty NAD T163. It would be nice to get some feedback on the processors listed here: Marantz AV7703 ($1500) Yamaha CX-A5100 ($1700) Onkyo PR-RZ5100 ($1800) They are reasonably priced, but I'm cheap so I tend to go for the bottom dollar unit. Which of these is...
  7. System Setup and Connection
    I have Sony SS TSF500 (3 ohm) speaker and Onkyo TX-SR444 connected, the problem is there is not much audio volume coming from the speaker. To check if it was speaker issue, I replaced it with another 3 ohm speaker but the result the same. Also I reset the Onkyo AV incase there was some setting...
  8. Home Theater Receivers | Processors | Amps
    I’ve had my Onkyo 809 since 2012. The audio or HDMI went out right after warranty expired. They however fixed it. It’s now going out again I decided to purchase the Yamaha RXA870 Now my subs are very weak. I am running the inuke nu4-6000. Any thoughts? With my track record with Onkyo I...
  9. Home Theater Receivers | Processors | Amps
    I had the Onkyo TX-NR838 7.2-Ch set up in my home and it worked like a charm. I had two PSB bookshelves and Onkyo Atmos heights in the front. I had Bose Satellites for my surrounds and PSB For surround rears. Plus a powered sub. The Atmos sounded so great and added another set of listening...
  10. System Setup and Connection
    Hi all...I have been through Internet 2 days now but I just cannot find the solution for my problem. I have (all are Onkyo) some components that somehow I can't get it go work properly. I have the onkyo tx-sr608,the cd dx-7511,the minidisc md-2321 and the double cassettedeck ta-rw244. The...
  11. Home Theater System Recommendations
    Hello , sorry for my english , it is not my native language . I live in Belgium , europe . i would like to replace my old audio system. My room is 4 by 6 meters with the tv on the 6 meter wall. The system will be used 60% for music , 40% films. I've been reading about the Onkyo TX-NR676...
  12. System Setup and Connection
    Something has change in my setup as it does not behave as before When I watch movies, it comes from my plex server to my Apple TV to my receiver (TX-NR709) Before when a movie was in 5.1, It would show on my receiver (most of the time) as Doby D. Now I see multichannel all the time setup on...
  13. REW Forum
    I have an Onkyo 5507 and running REW (using a loopback) with an ECM8000, mic amp and a SoundBlaster Live 24 bit USB soundcard. When I run a measurement with the Onkyo in direct mode, I get: Delay 8.81±0.01 ms (3.023 m, 9.92 ft) relative to Loopback but when I run it in stereo mode, I get...
  14. Home Theater System Recommendations
    So for those that are fans of onkyo and anyone else with some good input pleas chime in. Currently have Onkyo TX-nr709 and one of my zone 2 speaker outputs died. Thought what the hell time to upgrade. Now the 709 does do everything I want and Im very confortable with the controls so I feel...
  15. REW Forum
    Hi, So i've finally got the chance to give everything a good spin on this, it's the easter weekend and plenty of time to mess around. Forgot my charger from work for my laptop but i've got a replacement coming tomorrow and want to be prepared. I gave this another run today based on the advice...
  16. Onkyo
    Thought I'd post this in the Onkyo section as well as I'm not sure what the problem might be: New member with a big question. Recently moved and now can't get the rear surround speakers to fire on my old Onkyo HT-R150 system. Prior to the move I was running all audio through the cable box with...
  17. Home Theater Receivers | Processors | Amps
    I have these two low performance receivers, but they do the job for what I need. Even though they are low powered, I still want to use the better receiver to get the best sound. I have two rooms to use them in, one with a 5.1 setup and the other with a 3.1 setup. The 5.1 setup is using three...
  18. REW Forum
    Hi, I'm sure its not really meant to be for AV amp this whole software but it is trying to pick values a) that are outside of the range i give, i put 6db each and secondly, i can't just pick a frequency, it is fixed, how can i put this into REW? and if i can only do 6db + or - is it possible i...
  19. Onkyo
    I have owned an Onkyo 876 for years and have always had an issue with component not working properly when output through HDMI. It has only become a practical issue lately because several devices I have recently have started using has that as the highest Video output available. The wii is mew to...
  20. System Setup and Connection
    Hi, I am wondering If im doing anything wrong. I have had issues using my 876 with Component In with an HDMI out. I have the source selected, Component In set to that source, and I get picture. However it is messed up. I get digitization, Horizontal Tearing, Warbling, SNOW, all sorts of...
1-20 of 500 Results
Top