Home Theater Forum and Systems banner
parallel
1-11 of 11 Results
  1. System Setup and Connection
    Hi, I have a bluray samsung home theater system which I would like to connect two sub in parallel. The home theater sub out is rated at 3ohm 175 RMS. The subwoofers I want to connect are 6ohm and 135RMS. Could I connect them in parallel in order to drop the inpendance to 3ohm? Or connect them...
  2. REW Forum
    Hello there! Thank You a lot for your brilliant work! I love your software, and I am enjoying it wast 3 or 4 weeks trying to do the best possible results in my first studio (I am just 27 :D). But my problem is how to generate more than just 20 band EQ (Generic) because i would like to use 2 or 3...
  3. Home Theater Receivers | Processors | Amps
    I have a Pioneer HTZ818BDW home theatre system connected to my computer via HDMI. When I play music on it, it only plays from the front left & right speakers. I'd like it to play from the surround left & right speakers also. I've tried connecting the surround speakers to the front speakers in...
  4. DIY Subwoofers - General Discussion
    Is there a way to wire 4 X 4 Ohm SVC Drivers and com out with a final Load 4 Ohms? This is not an option on the wiring diagrams. Could you wire some in parallel and some in series to come out with 4 Ohms? 4 x 4 Ohm SVC Drivers / Final Load 1 Ohm
  5. System Setup and Connection
    Hi everyone! I'll post this in the wrog forum so I'm reposting it in here. I'm not expert in this subject and thats why I comming to you for help. I have 2 areas Living Room and Deck. All of my Video sources are in the LR (DirecTV HD and PS3) connected to a HTS - Home Theater System (nothing...
  6. Home Theater Design and Construction
    Hi everyone! This is my first post in here. I have in my living room one Home Theater System working great. Is in this area where I have my PS3, Direct TV and Blu Ray. Next to my living room it's my deck. In this deck I've installed a Projector with a Projector Screen. I want to have a surround...
  7. REW Forum
    I'm using REW v.5.0 to measure a woofer, tweeter and both in parallel. The woofer is a Tang Band 6" unit, the tweeter is Fountek 3.0 and all are mounted in a box. The amplifier is a $100 Sherwood 2 channel receiver from Radio Shack. When I measure the woofer and tweeter in parallel(using a 30uF...
  8. System Setup and Connection
    I have been a bit confused by some electrical engineers recently when I brought up using a pair of speakers for a center channel. It basically boiled down to two 8 ohm speakers can never be wired to draw 8 ohm and that confused me. How can adding more drivers change the ohm load if a speaker...
  9. Pro Audio
    Hi, I'd love to hear how everyone is using compression with drums. I like to take the whole drumkit (every mics to one bus) and trash it in a compressor , then EQ it (add high mid and low end) and then blend this with the existing drum mix. I would also sometimes take the kick and snare...
  10. Home Theater Receivers | Processors | Amps
    I need help to clarify this situation ... :hide: I have a pair of speakers in a parallel connection; my AVR output 140WPC @ 8ohms and 230WPC @ 8ohms with a 4 ohm load (is a little confusing, but a review of the AVR said that when using a 4 ohm load to leave the AVR impedance at 8 instead of 6...
  11. Home Audio Speakers
    Hello, I am working on biulding an electronic x-over to replace the passives in my Diffinitve Technology speakers. I have the direct firing Dappolito array mains each with two 6.5 in. woffers and one 1 in. fabic dome tweeter. My question is after I complete the x-over I am not sure if I sould...
1-11 of 11 Results
Top