Home Theater Forum and Systems banner

plate

  1. Subwoofer Amps | High Pass Filters
    like to use the paradigm seismic plate in a ported build with CSS SDX15. i dont have the power entry module from the cabinet, but feel i could power the amp side and component side of the amp and bypass the entry module. any thoughts?
  2. Subwoofer Amps | High Pass Filters
    Hey guys, just wondering where to get good plate amps from in aus. Im looking for about 500wrms at 4 ohms. Any ideas?
  3. Subwoofer Amps | High Pass Filters
    I am toying with an idea for a sub that will require a plate amp that is narrowish and not to deep. The narrower they are the deeper they can be. I was hoping for 500-1000w. The BK amps look promising, but I can't find a dealer on this side of the pond. I saw some of the DSP amps but at prices...
  4. Home Audio Subwoofers
    I just bought an Infinity Entra, everything except the amp. I was looking at PE plate amps like the BASH 300W model, and I was thinking that I could simply get a peice of metal machined to account for BASH's smaller plate size ( the Entra has a 12 1/2 by 6 1/2 opening). Besides cabinet volume...
  5. Home Audio Subwoofers
    I have a Emo sub12 and the plate amp has failed twice on me. It is still under warranty, so it should get fixed again no problem, but I wanted to think ahead. I suspect it will fail again out of warranty. Does anyone know of a direct fit plate amp on the market?
  6. Subwoofer Amps | High Pass Filters
    I bought and have a MiniDSP amp version coming in the next few days and need some advice of how to wired it. Right now I have a dual sealed opposed 15" sub (JBL GTI MKI DVC6ohm drivers) wired for a 6ohm load. I'm thinking of adding a second box with one 15" GTI driver for a total of three...
  7. DIY Subwoofers - General Discussion
    Hi Guys, I'm looking at getting a Tempest X2 15" but I am wondering what plate amp and wattage I should get to go with it. I am looking to build it into a ported box and maybe around the 15Hz range if that low is possible. I have been watching threads here for a while but lost on amps as...
  8. Creative Sound Solutions
    Well I finally got all my pieces and started building this week. I had a stroke of luck at a local specialty lumber store near me and found 3/4" mdf with fir veneer on one side and cherry veneer on the other. I am using the cherry side for my box. It was just over 4 cu.ft. to start , but with...
  9. DIY Subwoofers - General Discussion
    Anyone have any info on the specs for this amp? I can get a good deal on one, just want to see what its capable of.
  10. Subwoofer Amps | High Pass Filters
    is it possible to hook up 2 subs to one plate amp? if so, how is it done?
  11. Subwoofer Amps | High Pass Filters
    Hey all, quick parts sourcing question from a n00b. I'm going to be building a sub in the near future and will need to power it with a 200w-300w amp. I've checked PE, they have their BASH 300 in stock for $150, the Dayton 240w is out of stock and looks like it will be available about the...
  12. DIY Repair and Maintenance
    I'm replacing a blown cap on a plate amp that I got (for free) off an "Acoustic Audio HD-sub12" subwoofer. I'm no electronics wiz, but I can read the side of a capacitor, and I can solder... The vendor claims 400W RMS and 800W peak. The amp does perform reasonably, but I don't really have...
  13. SVSound
    Have a pair of PB12-Ultra/2's (used, org owner bought in 2007 he said) that have some TX hum that I didn't notice originally... not a biggie (so far at least) - and not ground loop related, not thru the woofers, no other sub/amp/speaker has this in the same room/same ckts, etc has it, no FL...
  14. Remotes | Cables | Accessories | Tweaks
    Hi everyone, Still farely new with HT but read lots of threads about wires, connections, wall plates etc... Just got a new house and my basement in not finished. I am about to start the work soon and was looking at buying a bunch of stuff from Monoprice. Since my basement is not finished, no...
  15. Subwoofer Amps | High Pass Filters
    Does anyone know if this amp (gateway sw303 designed by HSU or used in a design for gateway by HSU or so I've read) has a eq boost to it? specs that I know of, amp specs SW303: 150 watts RMS (400 max.) Signal-to-Noise Ratio Greater than 80 dB Damping factor >500 Crossover SW203/SW303: 40-180...
  16. Subwoofer Amps | High Pass Filters
    Do you guys know of any plate amps that can run straight off the audio outputs from my tv? If you don't have a receiver in your bed room how can i add a subwoofer? It doesn't have to be 2.1 but it be nice. I know of the Dayton MCA2550D 2.1 Channel Class D Amplifier but it seems a bit weak and...
  17. DIY Subwoofers - General Discussion
    I'm getting ready to start a sonosub project, and I'm wondering how many out there built their plate amp into the main tube of the sub? I've already got the plate amp, so a rack mount isn't really an option, but I'm debating weather or not to build the amp into the sub or put it in a separate...
  18. Home Theater Receivers | Processors | Amps
    I am working on building a woofer/sub-woof using an old (but never used) MTX 10" Blue Thunder (auto-sound) speaker in a IB enclosure (per Audio X-Press April, 2002). My question involves powering same from a "plate amp" since that is about the same price as the parts for a x-over. I would...
  19. DIY Subwoofers - General Discussion
    I'm sure I saw somewhere that someone had one on the way, but I cant now find it. The US market is a bit harder for me to follow, so do any of you guys know anything of these, or have I got it wrong?
  20. Subwoofer Amps | High Pass Filters
    I am building a Dayton HF 12" sealed sub for HT/Music. I am trying to find the most affordable watt/dollar combo to drive it. I first thought about the Dayton 240 w plate amp, but was interested in getting something with a little more punch. I am not trying to break any windows, but I do like...
Top