Ill be short...
1. What I have:
Receiver: Sony DA2400ES
Sub amp: Behringer NU1000DPS
Speakers: 4x B&W 601 S2 as satelites, central to come later...
2. What I need to figure out:
Location for sub (I'll use just one sub, maybe much later I will add more, so i have to place it wisely)...
I m planning to buy a Klipsch Rf 7 series speaker package from US but I m worried if I ll be able to use them in India as in America it works on 120 volt I guess but in india it works on 230 v. Will there be any compatible issues?? Pls help... Thanks.
Hello friends Could you pls suggest which is a better and more powerful amp for a Klipsch Rf7 package? 1)Onkyo Txnr 5010 or 2)Onkyo Txnr 3030 Or can u pls suggest any other better one pls? Thanks a lot.. Aju Abdul Rahman
For some reason, I am having difficulty understanding the relationship between the Control Input Volume and the dB FS Output level shown on the REW SPL Meter. This misunderstanding arose after I entered the Sensitivity parameter for my UMM-6 USB mic into the calibration file, and then tried to...
Good morning guys and gals. I was lucky enough to get these speakers last night and I need some help identifying them pls. Maybe a model no and some specs pls or just a link as to where I could get some info on it. All info is much appreciated. Thank you.
would you help me to set primaries and secondaries from 0 to 100 in line? pls
at 75% it is way off
what else I can do to make it better?
this is for sharp 844 LCD in movie av mode
gamma target 2.35
the manual says it is 19.2" but does that measurement include the bottom support legs/pegs?
I have an 18" opening subwoofer cabinet and I want to know how tall is the Klipsch rw-12d without the support legs becasue I intend to remvoe them?
if you have or had this subwoofer can you tell me? do...
Would appreciate help troubleshooting the errors I see when creating a 'soundcard' calibration file. Using the Presonus Audiobox mic-pre and USB interface box (http://www.presonus.com/products/AudioBox-USB).
Have the output looped back into the mic/instrument input. Being careful to...
i have built a dedicated room for home cinema and listening to music. It is built out of solid concrete blocks 6" thick. I plan on insulating the walls with 2" rockwool battens held in place by plastic sheeting, all hidden by a black velvet fabric strung ceiling to floor.
The floor is...
I'm in a constant battle with my new room..... i've downloaded the program to get some measurments..
but i cannot even get through the soundcard calibration part...
i can only select my interface(motu8pre) as the input, nothing on the output.
i've managed to get some level on...
I am the proud owner of a new house (finally, no more condo!!!), and am planning to run in-wall speaker wires since I actually have both attic and crawlspace access and can do so without tearing out long chunks of drywall. No wires make wife happy. (ok, me too)
I'm hoping you all can lend me...
im building a projector and i want some good surround sound.
I want to build front and rear speakers with a woofer.
I dont know anything and could not understand how to start here.
Could you all help me start. I will manage the wooden box i guess...
but the technical part in audio, i...
I remember Craig said the Gizmo 1.0 was limited to an input voltage of 3 volts. Does anyone know if this is peak to peak 3 volts, or is it 3 volts RMS?
Reason I am asking is I am seriously considering building in a USB DAC using the bantham board with has a 5 volt p to p output. That is equal...
Alright, So I am now moving into the HT world from 12v.
I just picked up 2 13Ov.2 D4 drivers from ED http://www.edesignaudio.com/product_info.php?t=2&products_id=35
I want to make 2 16 inch sonotube enclosures for them. They will be powered by an ep2500. I have been doing a lot of reasearch...
Hello HTS folks,
I'm new here and googled 'home stereo forum' and found this great informative site. I have been viewing the forums and found some of the topics very interesting and informative, while others are way over my head as far as the technology goes. But, hopefully I'll learn...
I need help figuring out how to best integrate my mains. Here is what I have so far:
Sub is an SVS PB12-Plus/2 with ports set at 20Hz
I also have a house curve set:
This is what it looked like before I started (sub only):
Here is the first crack with the BFD filters...
Posted the first of the graphs over on AVForums, but pointed to the REW forum here for more advice.
The blue line is the in phase graph, the green is 180 phase. I was reasonably happy with the in phase but needed to sort the dip at 62Hz and the peak at 45Hz.
In an attempt to move...
I am about to but one of the units but I have some questions:
1) Neither the parametric filters frequencies values nor the fine tuning values are indicated in the FBQ 2496 manual while they are very well explained in the DSP 1124 P. What is making me think they may be different is that the...