Search Results for ‘powering’

So I plan on building a sealed JL 13w7 with EQ to hit 20hz flat, to power that little beast I was wondering if I should get an Behringer EP2500 or a Crown XLS 2502. Personally I'd like to go with the Crown, better efficiency + no need of mods for silence, but I wonder if it can handle the task...

Hi, my name is Steven and I stumbled across a thread regarding a Mitsubishi ws 55313 that won't power on. I haven't seen my exact issue, so I'm making a new post. Sorry if I overlooked an existing one with my exact issue. The TV had error code 22, and I have already replaced the convergence ic...

so I have this Kenwood KA-894 and want to incorperate it into my listening system whilst saving a buck. it sounds quite musical to my ears, but my DTA-100A(small Dayton Audio amp) still sounds better, so I plan on using it's hefty power for a subwoofer. 2x100 watts at <0.09% THD and 2x150 at 1%...

I scrapped the last heat sinks because they are in-adequate. One must use a wide extrusion type heat sink if not using any forced air cooling (otherwise known as forced convection cooling) New to me and maybe new to you. ? . Here is the modified material list- Omron 20 amp relay- Mouser...

Hi, I have owned a Samsung surround sound system with wireless rear speakers (model HT Z520) for a couple of years. There is a problem that has happened a couple of times and I am at a loss on what to do. My Samsung tv and surround sound are linked through the surround sound remote. The first...

I am having this same problem too with my HLR5667W. First I will give a background on what I have done so far. Initially I was getting the dreaded green checkerboard pattern on the analog channels, and the picture freezing on the digital channels that has been so prevalent in these sets, and...

Changed colorwheel after T.V. turned green and blue then blank screen with loud banshee like noise. After changing colorwheel the lamp wouldnt light up so I installed a new lamp, but still when I plug in t.v. it tries to power up three times with blinking lamp light then results in all three...

My Samsung just started intermittently powering off. I've seen a couple of times that before powering off "lamp and standby (red) lights flash 1-2 times". I wait a little, turn on again and sometimes stays on, but sometimes I have to the the same three times. I'm wondering if the heat has...

Hey guys, I'm creating a home theater setup and am now unsure of which route I should take. I bought a Crown XTi 1000 in order to power a sub. I realized after the line level inputs were unmatched because of the consumer/pro audio different in voltage. Therefore, I bought a Art Cleanbox to...

My system consists of SVS SCS-01s for L/C/R, and Paradigm atom monitor v5s for surround. PB-10NSD providing the subwoofage. The Atom monitors will be replaced with SVS SSS-01. Right now I have a 75wpc Denon avr-1706, and the SCSs are rated at 160w and 8 ohm speakers. It's used for my HTPC, an...

I'm a little concerned that my new Denon 3808ci will not provide enough power to the Monitor Audio GS60 surround speaker system for my media room. I previously had a B&K preamp and 500W amp supplying power to my Klipsh 15" sub and Polk RT3000 powered front speakers, center channel speaker and...

Approximately three months ago the light engine in this television was replaced which corrected the "blooming" issue. However recently, the TV has been powering off on its own and the red "lamp" indicator light is lit. I initially thought the lamp had blown, but when I pressed power, the TV...

A friend of mine has a WD-52327 and after removing his front screen assembly to clean the lower mirror, he reassembled the set and the picture was much improved, however he cannot turn the television on or off using the remote or the front panel. If he turns off the surge protector, of course...

I was curious to know what people think about using a single five/seven channel amp versus a two and a three (five channels) or two twos and a three for seven channels. When using multiple amps, is there a rule of thumb for the power level of the amps. For example, the rear power amp should be...