Home Theater Forum and Systems banner
preout
1-12 of 12 Results
  1. System Setup and Connection
    Until now i have been using only 2 speakers and a sub, that was set up using the subwoofer crossover (reviever -> sub -> frontspeakers), but i just got some new speakers that i want to use in a surround, so that i can get the full experience when watching movies with 5.1 tracks. I thought it...
  2. System Setup and Connection
    Hi Please i am newbie here in forum i need your helps sorry for my bad language english because i speak french only my config is : Avr : Marantz Sr7009 Amplifier : Nad M25 Speakers : Klipsch RF7 MKII , RC64 MKII ; RS62 MKII Before buy my amplifier Nad all its work fine my 2 front speaker its...
  3. Home Theater Receivers | Processors | Amps
    I apologize, if this question have been answered already. I tried to find an answer for my question, but couldn't find it. I'm going to buy a Yamaha RX-V463 5.1receiver to connect a panasonic surround speakers, and with the intention to use its preamp to power my samsung d5300 home theater...
  4. System Setup and Connection
    I just upgraded my old Pioneer VSX-517 to a Denon x-4000. Big inprovement. Now the Pioneer has no home, and I am thinking about using it to amplify the surround back speakers. Save me from having to buy another amp. Plus the Pioneer sounds pretty good and has 100 watts per channel. Is this an...
  5. Home Theater Receivers | Processors | Amps
    I just picked up a factory Refurb 4311 and I can not seem to get the SW2 (subwoofer 2) preout working. I have enabled two speakers for the subwoofers in the speaker config menu. No sound comes out of my 2nd subwoofer when it's connected to the SW2 input. When I plug it into SW1 input it works...
  6. REW Forum
    When I was using a "legacy" REW kit (EMM-6, soundcard, mixer), I measured the Pre-Out signal in order to compare the original signal with a signal with room correction appied (e.g. Audyssey). A typical graph looked like this: Now that I have replaced the legacy kit with a USB mic, HDMI...
  7. System Setup and Connection
    Hello all, hope everyone's holiday season went well. I have a denon avr 1804. I also have a tube amp kit currently in Montana on its way here as we speak. Also, i will be building a GR research Kit soon. Here is my question. I know this isn't the "right" way to do this, but here goes...
  8. System Setup and Connection
    Hey guys, I have the L&R preouts (mains) of my receiver driving a Crown amp driving my mains. I would like to connect another pair of mains to the receiver's front L&R speaker terminals and drive the second pair of speakers with the receivers's amp. Can I do this without any detrimental...
  9. System Setup and Connection
    I have a denon avr-2105 and a mirage 10" powered sub hooked up to a berringer feedback destroyer and it sounds great,,,,BUT,,,,when I select "stereo" or any 2 channel source my sub will not operate. What if I wear to use the per-out LEFT & RIGHT whit a"Y" rather than the LFE port? would it...
  10. System Setup and Connection
    I am trying to set up a multi-room system with a Yamaha RX-V671 to run my 7.1 in the main living area and external amps to run speakers in several other rooms in the house. I do not wish to run a volume control to each room, so I'd prefer to set the volume on the external amp and have it...
  11. Home Theater Receivers | Processors | Amps
    I have an insignia NS-R5101HD receiver and everything was working perfectly until about a week ago when I plugged it into my DVD player, then when I went back to the AUX2 output the sub no longer gets a signal. I've tested the sub and cord and both are fine. I also don't have the remote so I...
  12. System Setup and Connection
    Hey Sonnie, new to this forum, and just have to say everything you have built in this forum is very impressive and serious in design and construction. Love it all. The riser FI, sand fill damping, and the LLT's especially. I do have a question that I think has had some discussion before...
1-12 of 12 Results
Top