Home Theater Forum and Systems banner
process
1-14 of 19 Results
  1. REW Forum
    I understand that I need to take measurements of each channel of my stereo system separately. I also have a decent idea of how to apply EQ to each channel using a house curve. I assume that once I create the EQ filters for each channel I will want to measure the combined effect with both...
  2. Computers | HTPC | Media Servers
    Is there a list somewhere of laptops that can output 8 channel audio through the HDMI port?
  3. REW Forum
    Hi all I would like to design and build a 2 way system based on some speakers I have obtained with no available data. I have only commenced reading on the topic however I understand I will need to obtain impedance measurements of Thiele and Small parameters to design an enclosure, then measure...
  4. REW Forum
    Hello everyone, I am EXTREMELY frustrated. I am attempting to follow John Reekie's 90 deg cal file process, but for the life of me i cannot figure out how to delete a COLUMN, NOT a line, in wordpad. or any text editor for that matter. i need to delete the amplitude column, leaving only the freq...
  5. REW Forum
    I've followed / used the work of Dr. Earl Geddes to tune automotive audio systems professionally to down right spooky / lifelike results. I used specialized commercially available hardware and software to achieve this. But who can afford this if they want to apply similar principles at home...
  6. REW Forum
    Is there a flow chart or process somewhere for room analysis and correction? OK, so let me be a little more specific. My purpose is to set up and correct my Home Theater / Stereo Listening room. I envision a standard process, the most efficient order to perform specific tasks and the proper...
  7. REW Forum
    hi, this is my first post in this forum, i expect to dig deeper and deeper in REW in the future by practising. today, i just got TASCAM US-144MKII together with behringer DCX2496 arrived in my home. with my radioshack 33-2055 SPL, i'll be able to perform REW measurement during following...
  8. Home Theater System Recommendations
    Hello, I posted in the newcomer forum asking for advice. Thank you for your words of welcome and the advice given. I have a great home theater space in a home just purchased. Everything was removed. There is wiring for 12 wall sconces and a 7.1 surround sound system. It is wired for a ceiling...
  9. Home Theater Room Photos (Finished Rooms Only)
    Hi All, Thought I'd share a link to my home theater build. Enjoy, and let me know if you have any questions or need tips if you're in the process of building your own. -Andrew http://cid-4bc66119ba5cdf52.photos.live.com/browse.aspx/Basement%20Home%20Theater
  10. Electronic Processing/Equalization Devices
    I'm running in circles with all of this awesome info in trying to figure out how to process sound in my subs. I am less than a week away from completing the first of two enclosures on my SDX15 and am anxious to integrate it with the rest of my system. I have an older Nakamichi 5.1 receiver...
  11. SPL Meters | Mic's | Calibration | Sound Cards
    I have a Behringer uca202 external soundcard that I have calibrated successfully. I also have an ecm8000 with cal file. I just got a Xenyx 802 and am ready to start doing measurements. Does the 802 need to be calibrated? Would I just put it in the feedback loop while doing the calibration of...
  12. REW Forum
    Dear HTShack-mites I am about top start sound calibration of my first HT.Before I start thread of my own just need some inputs to get my basics right for calibration process. 1) For sound clalibration ,do you take readings from individual speakers(L,C,R etc) or just from Right speaker 2) My...
  13. DIY Subwoofers - General Discussion
    Some of us build subwoofers which can reproduce sound with a fairly flat response down to as low as 15 or even 10 HZ. What would be the point of building such a subwoofer if the source componants, amps and EQ's rolled off around 15 HZ, or if they were around -6 to -10db at 15 Hz. If this were...
  14. REW Forum
    I've read through the REW help file 3 times now. It never mentions in the setup and calibration process on when to load the SPL meter correction file. When should the SPL Meter correction file be loaded? Before Checking Levels? Before SPL Calibration procedure? Before Making measurements??
1-14 of 19 Results
Top