Home Theater Forum and Systems banner

qsc

  1. Home Theater Receivers | Processors | Amps
    Could the cx302 be used as a sub-woofer amp?
  2. Home Theater Receivers | Processors | Amps
    I am almost finished my home theater!!! Finally!! I am looking to buy an amp to power 4 15" Dayton Ultimax in a sealed box. I am currently looking at 3 amps and wondering the follow: iNuke 3000 QSC PLX 3402 Crown XTi 4000 Is the QSC PLX3402 or Crown XTi 4000 amp a good amp for driving...
  3. Home Theater Receivers | Processors | Amps
    I am looking to amp my home theater with QSC PA style amps, the issue I am facing is converting the RCA amp pre out on my Marantz 7007 to a signal that is usable for the QSC amps. Looking to convert it to balanced XLR with the cleanest sound possible without any additional distortion. I have...
  4. Subwoofer Amps | High Pass Filters
    I have a quick question before I do the fan mod for the QSC 1850HD. I have the digikey replacement fans that have been recommended. My question is about the connector where the fan mates to the QSC's circuit board. Can I order the connector so I don't need to cut the wires on the original fan...
  5. Sealed Subwoofer Build Projects
    I have just received a QSC 3602 amp that I am going to pair with a couple of 3.5 cu ft boxes that I am building. What drivers would work well in this box now that I have some decent power to drive them (1100 watts at 4 ohms). The reason the box size is fixed is that I am adding these to two...
  6. Home Theater System Recommendations
    I was pretty much set on getting Hsu VTF-15H powered sub, but while looking around for a good, used power amp, ran into a DIYer that has 15" passive sub(s) for sale (Cerwin-Vega ported design). Based on the body of work and equipment rack I've seen, which is just photos via text so far, I'm very...
  7. Home Theater Receivers | Processors | Amps
    Good evening all i acquired 2 qsc rmx850 that i would like to use to power my klipsch rf-52 in bi-amp mode silly questions but do you set both amp channel to the same gain DB ?? Or do you need to use a spl and set both channel independently to achieve the same db? Alain
  8. Home Theater System Recommendations
    I plan on using the QSC to power a pair of SVS 16-46 passive subwoofers. I have a BFD on backorder, so that will also be utilized. My Yamaha AVR has two subwoofer output jacks. Is it better to have the QSC settings on *stereo* or *parallel inputs*? I would prefer to utilize only one...
  9. REW Forum
    Is there any plan to enhance REW's support of the QSC DSP-30 EQ? I noticed REW doesn't fully utilize it. The DSP-30 has the following unused features: High Shelf Filter - 20 to 20kHz in 0.1Hz steps / -120dB to +12dB in .1dB steps / Q of .5 to .75 in .001 Q steps Low Shelf Filter - 20 to 20kHz...
  10. Subwoofer Amps | High Pass Filters
    I'm trying to decide between these three amps (edit - as well as a pair of Dayton SA1000s) to drive a diy subwoofer with dual-opposed 4 ohm JBL made Revel 15 inch woofers. The Revel Ultima amp was rated 700w, and these four amps all have that power. The Outlaw mono amps I'm currently using run...
  11. Subwoofer Amps | High Pass Filters
    Hey, any HTS members perform a fan mod to their older QSC Series 1 (1400) or USA Series (850/900) amps? I was interested if anyone was able to achieve near silence with any particular fan or modification, and if so, how they achieved it.
  12. System Setup and Connection
    i have a qsc 900 .. and i'm wondering if u can connect it thru a playstation via optical connection?? if so what component do i need to get?? thanks in advance!
  13. REW Forum
    Let me start by saying thanks for the software and ALL the help on the forum. Yes, I am still somewhat lost, but working my through... I noticed some old threads about using REW with a QSC DSP-30. Has anyone had any good (successful) experiece with geting REW to work with a DSP-4 or even...
  14. Subwoofer Amps | High Pass Filters
    Any thoughts on the new line of amps available for pre-order. GX series uses same Hclass as PLX, very light chassis, and very inexpensive it seems.
  15. Home Theater Receivers | Processors | Amps
    I have a chance to get some used QSC amps (Series Three 3500 and/or MX1500-each about 300-400 wpc @ 4 ohm/2 channels) for $200 each. I'm worried about the noise floor and the potential distortion since they are rated 20-20k at 0.1 THD. My mains are Dahlquist QX10s which are 4 ohm and rated...
  16. Home Theater Receivers | Processors | Amps
    Hey, I just got my QSC MX-700 amp in and got it hooked up. Very excited I grabbed the remote turned er on and played some music. To my disappointment there was barely any output! I had both chan 1 and 2 gains full and there was barely any bass. I checked all my connections and everything looks...
  17. REW Forum
    Hello all, I have been researching the forum and I downloaded the REW. I ordered a creative sound card which should arrive in a week. I have a hometheater system with balanced outputs to the amps and sub. I planned on buying a pair of QSC DSP30's(they are 2CH) to use as parametric EQs for the...
Top