Home Theater Forum and Systems banner
replaced
1-12 of 13 Results
  1. System Setup and Connection
    Sony SS-MF550H speaker. Problem: Which setting do I use and where do I put the Digital Multimeter ends to test if Caps are bad or if tweeter is blown? How do I find out what to replace?
  2. Mitsubishi
    Per this very helpful site, I had a friend solder in all 7 caps( 1000 25V 105 C) in my 2002 55 inch Mitsubishi set. He does it for a living. That fixed my blinking light issue thankfully! Now I have picture but it has a reddish hue. Unless I go almost fully down on color or tint, do I pull this...
  3. Samsung
    Hi Folks- Ten days ago I turned on my Samsung HVM5525 RPTV and the convergence was way out of whack. So I researched the issue especially on this site. I pulled the board, double checked every resistor and carefully replaced the STX IC's with new Sanyo parts sourced from B G Enterprises...
  4. Samsung
    I have a Samsung HLS4266/XAA that is a few years old, and recently it exibits a problem where it turns on, displays on the screen, and turns off after a few seconds. The Red lights on the power button come on. "TIMER" AND "LAMP" are in green and "STANDBY/TEMP" are in red. I replaced the lamp...
  5. Samsung
    Hello All: I received my digital board in the mail today and installed it in my HL-R5067W. Now, I don't have any sound and no option on the screen for Component so no HD. All it has is TV in my Source List I have a coax running from the wall into my cable box into the TV. That seems to give me...
  6. Philips / Magnavox
    I replaced the IC's in my 60pp9202/17f. I turned on the TV only to find It did not fix the problem with the Blue being pulled in at all four sides and not being able to adjust the convergence up or down for the Blue. Side to side is ok. So I did more research and found this site. I found...
  7. Samsung
    Hello everybody, I am brand new to this forum and hope somebody can help me out. I have a Samsung HLR6167WX DLP TV. From the many posts I have read it sure sounded like I needed a new digital board for my TV. (Green fuzzy screen, power randomly cycling) I purchased the very expensive Digital...
  8. JVC
    I just replaced the convergence chips in my JVC AV56WP74 TV and am running into a problem. I replaced the stock chips with a pair of Sanyo STK394-160 chips and am pretty confident in my solder connections. But when I powered up the TV the convergence wasn't as bad as before, but still out of...
  9. Samsung
    I was told to post this here. I just replaced the color wheel in my Samsung HLR6167. I put everything back together and the lamp won't light. I first get a green lamp light blinking then I get the other two lights that say Stand by/temp and one other light. It sounds like TV tries too reset and...
  10. Hitachi
    So as a project, I purchased a used 43UWX10B off of craigslist. I purchased it knowing that it had convergence issues. I ordered the X480293 kit (Sanyo), and replaced the IC's and the resistors. It looks like the repair had already been attempted because of the of the resistors in question had...
  11. Mitsubishi
    Having a problem with a Mitsubishi wt-46805 - I'm trying to fix my father's TV that developed convergence issues. I replaced the STK392-040 IC's with new ones from Acme and it fixed the convergence issue, however now the picture is really dim. The picture seems to be dimmer on the right side of...
  12. Home Theater Projectors
    Hey all. I just got my HC1500 and set it up on the floor while my old 4805 (800 hours on bulb and professionally calibrated 1 month ago) was still mounted on the ceiling. The HC1500 will be replacing the 4805 this weekend but I couldn't pass up the opportunity to compare the two units. Besides...
1-12 of 13 Results
Top