Hey, I’m new to REW and am learning every hour. In my situation I have to run java for now as I’ve tried every suggested troubleshooting but cannot get asio to recognize my hdmi connection. So I’m running my umik and denon 1400 with java for now.
I am in the process of measuring speakers...
I just bought a DC and did a first typical calibration , i am using SVS PB12-NSD and i was hoping to see a decent flat curve but i see it is more or less better after 35Hz . is it good? how can i improve further any advice?
I see the response starts very low is it normal?
I know this particular subject have been discussed countless time.
General consensus is that since I'm used to hear loudness eq curve so I will feel that flat sounds thin. I kinda accept this explanation.
However recently I have compared YPAO result of my A3050 with sennheiser HD 800 (using it's...
Ok, so I decided to do some EQ'ing of my system. All subs are crossed to the mains at 100Hz in my AVR.
Equipment: (All subs are receiving the full low end signal. No crossovers between them.)
1x JBL 4645C clone
2x Martycubes with Dayton HO 18's
1x 25Hz ported box with 2 Infinity 1260W's
I am a total newbie at this, just got an Umik and after a quick reading of REW manual I tried to measure my speakers for the first time. My setup is for hi-fi listening, not home theatre. I have two bookshelf Harbeths on stands in a room roughly 5X7 meters. Speakers are on the short side, I...
I am trying to measure/verify speaker delays and I'm getting strange results.
I have the recommended setup from the manual with a sound card. Right line out of the sound card goes to both the sound card left line in, and to the center channel analog AVR input. A RS SPL meter connects to the...
I'm using Rew since a couple of days. I've a Velleman Avm2050 and a Audyssey Mic
the graph below is taken with a Audyssey Mic setup. no problem with my Realtek 887 . I calibrated it without any issue and I've the related cal file
I got this kind of odd result
the red line is the...
I took 3 sweeps at different volume levels (I calibrated each using SPL meter), no other changes.
purple = 85dB
green = 75dB
red = 65dB
The 200hz and up region is what I was expecting to see across the entire frequency spectrum. Look at how bloated the bass gets on the quieter sweeps. The 65dB...
I have calibrated this MacBook before using Soundflower without the USB interface and also with the Behringer interface. I sat down last night to redo the calibration and found I was getting odd results. REW flags the results as having a more than 170 db disparity over the frequency range. No...
Background, I picked up a UMM-6 from Parts Express and set up REW on my MacBook (running latest OS X 10.9.4). My goal is to use REW to more logically set the filters for my Velodyne SMS-1 and get a nice flat response from 15-80hz with my Seaton SubMs HP+ Master and Slave setup.
I just bought a minidsp UMIK-1 and done some measurement and adjusted the PEQ1 & PEQ2 of my SVS 13 ultra Subwoofer to smooth out the SPL.
Now, the SPL seem ok but the waterfall and Group delay seem horrible.
Anyone can help analyze and explain to me the waterfall, Spectrogram, Spectral...
I`ve measured sound for getting RT60,
but the graph looks like step function...
what does this graph mean?
1. Why is the graph extremely folded about 90Hz?
2. What is the value of r at bottom part? ex. EDT(r:-0.0889)
3. Which value should I use as reverberation time?
Strange result when testing sound card calibration
This is my first time using REV and have experienced a strange result when testing the calibration of the sound card. As it is also my first real post I am not sure about including attachments. My sound card is a Creative SB X-fi. I...
Battlefield 3 color mod could result in hack ban
Heads up, Battlefield 3 fans: DICE doesn’t look kindly on you bringing mods to matches. Commenting on a mod which adds a splash of color to the military shooter, DICE’s Gustav Halling said using “those hacks” could result in...
First sorry for my poor english, but i will try to explain my problem.
I installed REW and i did all the steps off calibration sucessfuly, than i measured my control room with my KRK speakers and then i use the eq settings to create the filters adjustment to put on a plugin o cubase...
If I use a length of 128, my graphs look reallllllly nice and impressive (to me anyway). The higher up I go in length, the worse they look. At 512k, I get a complete null drop at every 50: 50hz, 150hz, 250hz (see attached).
I'm thinking that my PC must only be able to handle the 128 Length...
Good day, I have a problem with sound card calibration and loop back results.
I follow help file "Calibrating the Soundcard" step by step. All sound effects are switched off. Proper line in and line out are connected. My sound device is mother board integrated "Realtek HD Audio".
Is it possible to plot 2 meters at the same time?
I was talking to a friend of mine about speakers and he mentioned somthing that i wonder about now.
He said he never liked speakers with rear porting, he said somthing about phase or somthing. That the front of the speaker has a different wave...