Search Results for ‘rew’

Hi, My graph is a bit unusual. Can you take a look? I'm using a 5-inch book shelf speaker.(JBL) As you can see I have a dip of 100 Hz on both sides. However, it seems that 70~90hz is too low, except for the dip of 100hz.(Especially the left speaker. I tried to apply EQ only below 200hz to...

I'm trying to measure Thiele Small Parameters with REW. There's a tutorial in the REW support manual. I cannot find a USB soundcard that has a stereo (TRS) line input/microphone INPUT. The line inputs are only available on the old school desktop PC's motherboards or on those old PCI...

I don't have everything set up to test right now, but I have an ultimax 15 in a denovo audio 3 cf. sealed box (3 pounds of stuffing). When running REW measurements, there's a big drop in the frequency response below about 28hz. When I select "match target response", everything levels out...

Hi I just bought a MiniDSP 2x4 (not HD) and a UMIK-1. I am trying to do room measurement and doing some eq with my subwoofer. but I am not sure of what I'm even doing at this point! Do I set the AVR's volume to -0db? (I already did tone levels at -0db and set all my channels and sub to 75db(C)...

Hello, I am absolutely new to this area. I am reading (and trying to understand ???) with great interest the manual on the REM (Room Eq Wizard). I have a sound system including: a mixer 2 CDJ players 2 active amplified satellite speakers with DSP (Electrovoice) 2 active sub-amplified...

Dear All, I am using REW 5.1 on Mac El Capitan with a Scarlett 2nd gen 2i4 sound card and a Dayton Mic, both of them with a cal file. I am measuring RT60 on an empty room that is about 58K2 cubic feet. ( 1650 m3 ). I used two speakers and one sub to generate the sweep. I tried sweep ranges from...

Looking for some help. I have Marantz 8802a, two Sunfire amps, Goldenear one.r for fronts, Goldenear two for rear, supersat 50’s for surrounds, HTR 7000’s for ceiling, and two HSU subs. Since Goldenear speakers have their own powered subs, I effectively have six subs running from the two sub...

I was just thinking (scary...) it might be useful to be able to adjust sub integration in real time. What I mean is to have the mic at the listening position, your computer running REW near the sub, send 10-250hz pink noise through the appropriate channel(s) covering the speakers you are trying...

Hi forum-- I'm trying to use FB2K to play my sweep so that I can test my rePhase impulse+convolver. So other forum posts say to "Use acoustic timing reference" and check "Wait for timing reference". Ok, did that. But when I click Start Measuring, REW play a chirp and plays a sweep. It does not...

Hi forum-- Why does REW make me look up my calibration file every time I start it? Can't it remember this? Am I doing something wrong? Thanks, --Myles

Hey guys, it's been a while since I have been here. I just upgraded my subs to dual SVS SB16 Ultras. They sound great already but wanted to see if their onboard EQ can tweak the last bit of sound for me. My Microsoft Surface laptop doesn't have an HDMI out, but uses a display port out, which...

Hello Everybody, New member onboard from Singapore. Just trying to get more information using Room EQ (REW). Thank you very much.....Kenji:smile:

Hi. Looking to use JRiver's PEQ. Is there an Equaliser in REW that I could use for this?

Finally got REW setup and went through my first test. MDAT file attached here for those who wish to comment! Regards, Dan

Hello, This is my first post here and first stab at REW after lots of reading and video watching. I wanted to share what I did as a workflow and the graph I got so that someone can help me further as the results do not make sense to me. 1. Installed REW 5.19 with java 2. Connected my miniDSP...

Hi - I have spent a lot of time learning REW for purposes of placing and EQing my two subwoofers (SVS PB2000). I am now interested in getting a sense of how my other speakers (Totem Tribe IIs) are performing post YPAO(Yamaha 2070 receiver). The graph below shows the five speakers and the dual...

Hi, I'm learning how to install and use a house curve, specifically a hard knee house curve. I've copied the Notepad file and loaded it into REW under the house curve tab. But when I try to create a house curve with the EQ button, I can't find the symbol "House Curve" anywhere. I read the...

I have used REW on Windows for some time, but I've also started putting together an active stereo system controlled by a minimal install of Ubuntu Server. Since I assume REW on Linux requires a graphical interface, is there a way to simply record a frequency sweep through the terminal which I...

I am using REW V5.1 with an HDMI cable going from my laptop to my Denon X6400H and a Umik 1 Mic with the unique calibration file downloaded to REW. Why do I get this message every time I open REW.

Hi all, I just received my minidsp umik-1 and would like to know if my daughters Chromebook (c100p) will have the appropriate hardware to run REW correctly. It has two USB ports and what appears to be a micro HDMI port including your standard headphone jack. This is a pretty basic laptop and...