Home Theater Forum and Systems banner
rlp15
1-20 of 28 Results
  1. Ported Subwoofer Build Projects
    Hello, I apologize in advance because English is not my original languange (still studying it). I need your advise if this design will fly and what corrections do I need to do. I'm changing my HT to a different room and I only have a small space for my subwoofer on the rear corner of the room...
  2. DIY Subwoofers - General Discussion
    Ok, I've got dual RL-p15 LLT sonotubes, ~14Hz tune. They are the D2, serial coils, so dual 4Ohm load. I use them as LFE and >40Hz for the satelites. Now, being LLT they are a little lacking up towards the midbass area, and I would like to augment them a little up there. I have three Eminence...
  3. DIY Subwoofers - General Discussion
    Where can I get a replacement surround for the RLP15?
  4. DIY Subwoofers - General Discussion
    Hello all, I'm brand new to this forum but I have read some threads and found a sub woofer(Sound Splinter RL-P15) and amplifier(Dayton HPSA1000) that look like they will work for my application. I have not yet purchased them. I would like to get opinions on the combination and I need to know...
  5. IB - Infinite Baffle Subwoofer Build Projects
    I'm using 8 of the RL-P15s. The Vas turned out to be just right for my IB space which is 3 feet behind the front wall. It sounds wonderful:
  6. Ported Subwoofer Build Projects
    I've been asked to post a build thread of my passive radiator design in this forum to help others who may be considering a design using the passive radiator. My goal was to have a clean low end without having the port chuffing, huffing, noise, or resonance that can be associated with a ported...
  7. DIY Subwoofers - General Discussion
    Hi, I'm building a RL-P15 2ohm presented as 4ohm to the amplifier in a ported 10cu feet box turned to approx 14hz, I see alot of people recommending or using the EP2500 which is 2x750Watts (Claimed) How much power does the subwoofer actually need, if we talk true power outputs not claimed...
  8. Home Audio Subwoofers
    Hi, Its time for a subwoofer, its come down to: Velodyne SPL-1200R Velodyne SPL-1500R SVS PB13-Ultra SS RL-P15 2ohm ported with EP2500 and the quest for hard deep bass for action movies.....
  9. DIY Subwoofers - General Discussion
    What are the criteria for choosing between the dual 2 ohm and dual 4 ohm versions of the RL-P15's? The numbers are different on the drivers, but are those numbers representative of all circuit config of the voice coils? Or, do they represent the coils wired in series, for 4 ohm and 8 ohm...
  10. Sealed Subwoofer Build Projects
    This is my intention for my dual 15" RL-p in a sealed config. 2 - D4 RL-p's in a box that stands 46" tall, and 22" by 22" wide. I'm new to sketch-up, but was wondering about your opinions, I'll be using my old Adire Audio ADA-1200 to drive it wired for a combined 4 ohm load. The enclosure...
  11. Ported Subwoofer Build Projects
    My SS RL-p15 build *or maybe 18?* I'm just starting out this project, but might as well start a thread on it now. I've more or less decided to go with the Rl-p15, unless any of you would object to that and give me a better driver in that price range. I have a long term plan with this. I'm...
  12. Ported Subwoofer Build Projects
    Hello All, This is my first post but have been looking around for over a year now. I have a pair of RL-P15 that I have built a ported enclosures for and I drive them with a QSC 1450rmx amp 2 ohm load a channel (4ohm subs). This setup has been working good but I feel I am leaving something a the...
  13. Classifieds - Speakers and Subwoofers
    Hi bass heads! I'm selling two Rlp-15 D2 complete subs. They were powered with an EP2500 on each channel with a SMS-1 and they NEVER bottomed. They work and perform flawlessly. Each driver is in a 24" cube, 9cuft boxes tuned to 17hz. Each has a 6"X24" rear port. One box is unfinished and the...
  14. Classifieds - Speakers and Subwoofers
    Accidental second post.
  15. DIY Subwoofers - General Discussion
    Hello, Here is what I have available for cabinet space for a dedicated HT subs. 28" x 28" x 30" not including any bracing or the driver. Questions being what size port do I need and what is the best design for the port due to the size of the cabinet? What tunning should I be able to get with...
  16. DIY Subwoofers - General Discussion
    I am getting ready to do a sub-woofer for my home theater. I've pretty much decided on the Sound Splinter RL-p15 in a 2' cube sealed enclosure. I leaning towards the behringer 2500 despite their questionable reputation in the music instrument world. My budget is 800 bucks for the whole gig...
  17. Mobile Audio
    So if I was to put a rlp15 into my accord in a box similar to the recommendations on SS website (3.5 ported to 28) what kind of amp would you guys recommend. It has been years since I have messed with car audio so I dont have a clue of a good but affordable amp to drive this. Also, in the past...
  18. DIY Subwoofers - General Discussion
    Hello, Im starting on a sub project with the RL-p15 in a vented enclosure using 10 cu ft, (stated as optimum on the website), at fb=14.5Hz, I would like a sub that will play low & loud, the sub "footprint" needs to be about 21"x21", I'll be driving it with a QSC RMX1450, and now the questions...
  19. DIY Subwoofers - General Discussion
    Posted this in the Soundsplinter section. Any advice would be greatly appreciated so I can stop obsessing over this and mabey get to bed before 2 am. http://www.hometheatershack.com/forums/soundsplinter/4761-need-some-thoughts-large-dual-15-dual-ported-design.html Thanks, Erik
  20. Ported Subwoofer Build Projects
    Well, in addition to the 3.5 cu ft ported box tuned to 24 Hz, I decided to build a couple of LLT sonosubs for the two RL-p15 drivers I bought from Mike. These guys are 260 L (9.2 cu ft) tuned to 14 Hz. I started on them about a week an a half ago and right now they're finished sitting in my...
1-20 of 28 Results
Top