Home Theater Forum and Systems banner

router

  1. can I use a wireless signal router with directTV?

    System Setup and Connection
    Hi all, I'm hoping to get a lil help with my new setup. In our living room we have 2 TVs, one of them is for our main directTV box and the other is mainly used for gaming. Sometimes we want to watch directTV content on our gaming TV, but we don't want to have to hardwire the cables or run extra...
  2. Home router

    Chat Box SWAMP
    Good morning guys!!! I just set up Comcast for the new place we move in next month and needing/wanting to buy a new router was wondering if you guys recommend a good one that's not overly pricey. I was thinking about this one, any thoughts?
  3. Jasper Circle Jig vs Router Buddy and my Issues...

    DIY Speakers
    Just a FYI to the speaker builders or future speaker builders. I had a couple Jasper circle jigs. I recently upgraded my router to this amazing porter cable 7539. I just went to do some wood work and found that my Jasper circle jigs are now useless as the holes don't match up. I was pretty...
  4. Which router bits should I buy ? (Sonosub build)

    DIY Subwoofers - General Discussion
    For the end caps and for making flares, what router bits should I buy ? I need one to cut out the caps, and I need one to round the edges of the caps for finishing. I also need a larger one for the port flairs. Newfie Speed and Sport has several bits and sets...
  5. Router and Modem Upgrades

    Computers | HTPC | Media Servers
    I'm a little slow to upgrade when I have something that is dependable and works. Have had the same Chevy almost 30 years and a Buick for 18, both are dependable, have a lot of miles and cost very little to maintain. So when Comcast called a couple of years ago about my outdated Linksys WCG200...
  6. Router projector Setup?

    System Setup and Connection
    I'm in the market for a projector with an Ethernet port like Viewsonic PJD6223. My AVR also has an Ethernet port. I was wondering if the setup I have diagramed below would work if I use the HDMI cables that have the built in Ethernet cable from Monoprice.com. I’ m also not sure if the projector...
  7. Router Bits

    DIY Speakers
    I found a dewalt 618 fixed/plunge router on craigslist for $90 thing's like brand new! i need to get bits 1/4 spiral up cut and 3/4 flat bottom right? Carbide for sure. Where do you all get your bits or what brand do you use? There seems to be big price differences
  8. Router Suggestions

    Computers | HTPC | Media Servers
    The router I have from my telephone company that supplies my internet is A/G. I also have one of those GoFlex Desk usb 2 TB hard drive where I am storing my movies. My goals: I would like to do is be able to stream those movies to any of my computers and eventually the TV. I would get another...
  9. Best place to buy Router Bits

    DIY Subwoofers - General Discussion
    Where would be the best place to buy Router Bits ??
  10. Fixed router for making sub box ??

    DIY Subwoofers - General Discussion
    With a non plunging router can the driver holes be done . Is there maybe some tips on how to make the driver cutout with fixed router??
  11. ATON DLA6 6-Room Speaker Level Audio Router

    Computers | HTPC | Media Servers
    Has anyone had any dealings with this product? It has a remote that has a 200 ft range, to turn on and off in 6 rooms of speakers and control volume. Is there other products like this on the market? THIS You Tube explains what it is -
  12. Can you use a wireless router as just a Switch?

    Computers | HTPC | Media Servers
    I have my house wired with a cat-5 network. My existing router is a Linksys 8-port router that still works just fine. It is in a location that is really awkward to get to if any wiring changes are needed (don't ask). In my living room I have a 5-port 10/100 Linksys switch to give me more...
  13. Recommendations for Router for DIYer?

    DIY Subwoofers - General Discussion
    I'm building a HT sub and will (FINALLY!) bite the bullet to buy my own router. What routers do you guys use (make & model) and what is your opinion of them? BTW, I assume that most routers are compatible with the Jasper jigs, which I am also buying. I'm also assuming that everyone is using...
  14. Undercut with router :(

    DIY Subwoofers - General Discussion
    Hi, I have a bit of an issue and i was wondering if you guys have any advice for me. Basically i have cut a circle out of my front baffle for my subwoofer box i am building and to cut a long story short i have managed to cut the hole to small and the subwoofer driver wont fit. I have cut a...
  15. Router tips speaker cutouts

    Home Theater Design and Construction
    So I have been harassing my local Menards and Home Depot lately about as adjustable circle jig, and they don't have any jigs at all. I will check Lowes tonight, but expect the same. I saw some nice ones online, but I am anxious to get started on my break-in baffle and will use it as an...
  16. Router recommendation

    Computers | HTPC | Media Servers
    Just wondering if anyone has a recommendation for a wireless router? The one that came with my internet is the weak link (and out of warranty), so I'm looking for a replacement. I've read about the new Draft N stuff and that is not necessary, but I would like 4 gigabit ports, which would...
  17. Router Circle Jig

    DIY Subwoofers - General Discussion
    Split from "Need new sub, thought i would build one! Eric, how did you make your jig? Did you just measure to make the appropriate holes you needed for the cutout, recess, and port opening? I've been tempted to buy one of the nice jigs, but it seems like a lot of people have been getting...
  18. Router Question

    DIY Speakers
    My 30 plus years crusty old Sears router finally became unusable because the starter button pivoted on a cheap plastic pin that broke. While some ambitious person would have found a way to repair it, I found it as a good excuse to finally get a decent router. In any case, I bought a Bosch and so...
  19. Router Bits

    DIY Subwoofers - General Discussion
    I know this is kind of a lame question but my experience with routers is limited. I just bought a Craftsman 2HP router and wondered what bit you use to cut out your endcaps? Also, does anyone have a suggestion for circle or compass jigs? Not sure which one will fit the router or work best for...
  20. Recommended router bits to start out?

    DIY Subwoofers - General Discussion
    Can someone recommend what router bits I should start out with? I know we discussed it once in another thread, but I couldn't find exactly what I was looking for. Basically, what would I need if I were going to build a subwoofer box? Thanks!
Top