Home Theater Forum and Systems banner
Cancel

Search Results for ‘rss390ho’

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-8 of 8 Results

Search Tags

1080p 2007 2008 2009 2010 3d 4k advice amp april audio bass behringer blu-ray bluray box build calibration camera card center channel coming dayton denon design digital diy dual eq game giveaway good hd hdmi hdtv high home ht input issue issues lcd level listings live march measurement measurements member mic mitsubishi needed newbie october onkyo panasonic pioneer player post power prime problem problems programming project projector ps3 question receiver releases reported response review rew room samsung screen season series setting setup sony sound soundcard spl subs svs system test theater thread time toshiba tv ultra upgrade video wall xbox
  1. DIY Subwoofers - General Discussion
    Looking for feedback. 4 sealed 390ho 3-6cu ftft box Nx6000d or Crown with Mdsp. I am thinking sealed. From what I have read there easier to tune ? 3 up front behind AT screen ( want to keep the depth under 20 inch ) 1 behind the coach @ 20ft I can get 4 390ho for 1000$ CND funds Trying to...
    rss390ho sealed thoughts
  2. Ported Subwoofer Build Projects
    I am wondering if anyone can model these 2 Drivers in WinISD to see which is best suited for a 20Wx24Hx25D (4.4cuft Net) Sub enclosure for HT . SI15", TS Parameters: 15" D2 Re: 3.7 Ohms Fs: 18.5 Hz Qes: 0.37 Qms: 6.3 Qts: 0.35 Le: 3.5 mH Sd: 80445 mm^2...
    44cuft net ported rss390ho si15
  3. Ported Subwoofer Build Projects
    Hello. Currently. I Have a Dayton RSS390HO powered by a Yung SD-500 amp in a sealed enclosure roughly 2.0 Cu ft. Since this is a system that is now mostly used 80% home theater, I want to DIY a ported sub to get more extension for Bluray movies. The sealed cab sounds pretty good and is great...
    dayton hair pulling rss390ho
  4. Ported Subwoofer Build Projects
    Just a little info on my build. Currently I am using an older model 200 watt amp to power this so I’ll not be completely satisfied until a more power appropriate amp is purchased. The project was only approved if I could make it appear as an end table in our living/HT/Kids play room in...
    build rss390ho
  5. Sealed Subwoofer Build Projects
    Dayton RSS390HO 15", iNuke NU1000DSP build Hi guys, extreme newb here. I was just messing around with winISD with the Dayton Audio RSS390HO sub in a sealed enclosure. According to the graphs below I can get 90+dB all day down below 20Hz in a 2^3ft enclosure with just 150Watts??? I got this...
    build dayton inuke nu1000dsp rss390ho
  6. Ported Subwoofer Build Projects
    I have been planning to build a couple of subwoofers for a sound system (ie, HT and music) for our winter home for some time. I had been considering a number of manufacturers/suppliers but with AE and Exodus drivers essentially unavailable I purchased two from the remaining "contender"...
    build rss390ho
  7. Ported Subwoofer Build Projects
    Why does my Sonosub sound louder with the top cap off?? Updated with some Pics Driver- Dayton Audio RSS390HO-4 Enclosure - 18" dia Sonotube at 8.8 cuf. Damped with pink insulation. Amp - Behringer Inuke 3000DSP bridged to 4 ohm mono I had the top cap off today while I was waiting for some...
    cap dayton inuke louder rss390ho sonosub sounds top
  8. Ported Subwoofer Build Projects
    The original plan of this build was to actually make two subwoofers utilizing the Dayton RSS390HO driver. After I got this first enclosure roughly together, I ended up just building one due to size restraints in the living area and pleasing the wife. When I started assembly I noticed something...
    15" build dayton high output rss390ho
1-8 of 8 Results
Top