Hi,
Back in 2014, I bought an LG BH9430PW 1460W 3D Blu-ray Theater System when it was first released.
It is a powerful home theater system but had a lot of issues with its amplifier and rear speakers controller.
Now I'm left with working speakers and I was wondering if I can buy a good and...
I have the following drivers x 4, are they suitable for horn loading?
Etone 831, 200mm driver, treated paper cone.
fs - 41 Hz
Bl - 12.1
Qms - 3.59
Qes - 0.36
Qts - 0.33
Vas - 26.6L
Sd - 213.8 cm2
Spl - 90.3
Re - 6.8 ohm
Xmax - 4mm one way
Pe - 100W RMS
They seem to lack bass in the current...
Hi All,
I have a 12" driver with the following specs, is it suitable for a tapped horn project?
I've tried using hornresp but it just doesn't seem to work out. Can someone give me a hand?
Fs - 19Hz
Qms - 5.1
Qes - 0.43
Qts - 0.4
SPL - 90dB @ 2.83v
BL - 10.7
Xmax - 11mm one way
VAS - 260L
Le -...
<100€. It can be usb too. Which are the best?
"Cross Spectrum calibration lab has provided us with a graph of how various Behringer ECM8000 microphones and Dayton EMM-6 can differ in their responses. While many units are within an acceptable variance, some are not.
Read more...
I recently bought a Sony PCM-M10 handheld recorder, for "ripping" my LPs. The electret condenser microphones have a frequency response of 20-40k. Can't I just connect the line out from the PCM-10 to the inputs of my Behringer UCA-222? The nice thing about this unit is that it's already threaded...
Hey All, I'm hoping to get a few tips on treating a room for mixing (mainly dance music). Unfortunately, I am stuck with near-cubic room dimensions of 97" x 100" x 95" (wxdxh) and from what I gather from reading through a few threads, cubic room dimensions are far from favorable when trying to...
My system consist of Paradigm S6 (main), C5 (centre), PC-Ultra 13 (sub) and KEF Q50 surround. I power the system with Anthem P5. I would like to upgrade mainly my surround speakers.
The options I am considering are:
1. Buy S8 and use S6 as surround
2. Buy second pair S6
3. Buy Paradigm ADP 3...
hi,
previously i only use my receiver's internal generated noise signal to set up each channel speaker's level (75DB),
now i am going to have "start from zero" project to adjust my HT system(including measurements and all necessary adjustments).
before doing all these, i firstly will set up...
My first post in the REW section at HTS. So hello to those I haven't run into before. I have access to the following equipment and am wondering if it's suitable for taking room measurements, both in the low freq and full range...
Preamp- phonic 740 power pod deluxe
- Focusrite...
Good evening
I am about to start a DIY sub project with the mach5 IXL15.2.2 in a 5 CF box tuned to 20,74 Hz driven by the EP4000 and i need tHPF at 17 Hz according to the gentlemen who design the sub for me.
Since the Reckhorn B2 seems to be unavailable would the EQ.2 from elemental Design...
Hey all,
I have a pair of PSB Image T45's, a PSB Image C60 and a pair of PSB Alpha B1's as my home theater system currently. Im looking to add a suitable sub and complete my system.
I have a budget of around $1000 or a bit more. I have looked at the SVS SB12-plus and SB13-plus subs and they...
Hello,
Most A/V receivers come equipped with measuring microphones for automatic speaker setup. It is to be expected that these microphones are not linear and each receiver will match its own microphone response curve.
Assuming that the microphone curve is known, is it suitable for use with...
I was just curious as to others opinions on the suitability of this sub in IB? I am planning construction of a HT in the basement and am trying to come to a consensus on what to do about subs. Goals are to get very low and be reasonably clean. This room would be used mostly for movies and...
As per title,
Is a 2+2" sub frame/bracing/skeleton suitable for a large sub?
2+2" batton is cheaper and involves less work for internal bracing of a cabinet, so you could build an internal braced skeleton to glue and screw outer panels to with a square and a hand saw, drill and long screws...
I am building a dedicated HT room. Although I will also naturally play music also, but to a far lesser degree.
My equipment so far
Denon AVP-A1HD
Elektra T7 amplifier
Audyssey Sub EQ
JMlab 1027BEs
JMlab C1000BE
My room is only small at 17.4' x 13.5' and sloped ceiling. Giving a volume of...
Is the X curve suitable for home theater?
Part 2: An X Curve for the Center Channel?
House curve / X curve confusion
In Part Three of my article, House curve: What it is, why you need it, how to do it, we saw that the film industry uses a standardized room curve for both production...
Hello again,
First of all, I want this stand, and I can't find anything comparable anywhere!
The attached picture shows my room. The TV and audio in the picture is old. I have a new Samsung 61" DLP with Receiver, DVD player, XBOX, Cable box, and center channel. I like the above stand because...
i I would appreciate some wisdom as to how this amp might perform with a 4-5 cu ft box tuned to 16-18 Hz using a PE 12" Titanic driver (kind of a SVS NSD-12 clone).
Will listen to music, HT and some low Church organ stuff. Basement room is 50' X 12' X 7.5 '...
I have problems with the built in sound card of my computer... It can't read the Radioshack SPL meter input. So I am wondering if the "Soundblaster Audigy value" soundcard would work. Has anybody tried it?
Same question for the Creative live internal soundcard.
Appreciate your kind feedbacks...