Home Theater Forum and Systems banner

user

  1. new user help please

    REW Forum
    I am getting very little readings from this and I am a little confused. The only readings I get are from the Filter Adjust tab and the Impulse tab (attached) the other tabs show up blank after measurements. Any help is greatly appreciated. Thanks
  2. First time user, in a small room.

    REW Forum
    I am using REW on a Mac with an RS-33-2055 through a MOTU 896 converter, sound played back through a pair of old Mackie HR824's. My room dimensions are 7'4" wide, 11'4" long and 94" high. Basically a finished shed. Untreated as of yet, but full of other stuff. I am wondering about the...
  3. New REW user, first eq attempts, rather long...

    REW Forum
    I'll start by saying thankyou to everyone for the wealth of knowledge I've gained from just reading the forum, over some time. Now it's my turn to ask stupid questions :) First some details about the room and the kit. I'm converting one of my rooms into a dedicated HT here in the UK. The...
  4. First Time REW User

    REW Forum
    My first post here just wanted to say awesome forum packed full of info. Using Windows XP platform, RS analog meter, UCA202 sound card. Ran my first couple of sweeps and what a eye opener to say the least. Using it for sub sweeps only, 2ea stacked corner loaded. I am in my learning curve but now...
  5. WinISD User Driver Database problem

    DIY Subwoofers - General Discussion
    Hi, i have a problem with WinISD Alpha. I'm pretty sure there should be a drop down menu for the user drivers i create but there isn't. Does anyone know whats going on cos the software is useless to me unless i can put in my own drivers... Thanks for any help, Purp
  6. Emotiva UMC-1 Official Thread : User Reviews and Discussion

    Home Theater Receivers | Processors | Amps
    UMC-1 preorders are apparently shipping. I hope to buy one as soon as they have them in stock in their shopping cart. As a casual movie watcher it makes no sense to spend twice as much as the UMC-1, it's going to replace a Sony receiver in my pre-amp's HT Bypass loop.
  7. new rew user question on freq

    SPL Meters | Mic's | Calibration | Sound Cards
    i have a velodyn sms1 for my subs can i use the ecm 8000 mic that came with it for rew? i really dont need rew for low freq i want to run rew to check the rest of my response in the room does rew and the mics used go up to 20k ? i would like to see problems in my room . i was planning on using...
  8. Post Padding Thread

    Testing
    This is it... the famous post padding thread so that you can get your first five post out of the way quickly. The old post padding thread got wiped out accidentally... we apologize to those who may be inconvenienced.
  9. WS55807 User vs. Service Convergence Question

    Mitsubishi
    I've been reading a great deal about the convergence ICs and related components blowing in this and other models. I've also been reading that "overadjusting" convergence can stress and overheat the ICs, causing them to breakdown even sooner. Does this overadjstment apply only to user mode? If...
  10. Need help - new user

    REW Forum
    I'm having problems. I've been at this for hours and searching the forums and help documents but I'm still stuck. Here's where I'm stuck. I can't get a decent soundcard calibration. I have a soundblaster audigy 5.1 card. I'm hooked up through a behringer xenyx802 & ecm8000. First off, when...
  11. New user with a few questions about measurements

    REW Forum
    First let me say that REW is fantastic. Since I discovered it last weekend I can't stop using it! I have a DIY sub with a 12" Dayton driver and a 300 watt amp in a 2 cubic foot sealed enclosure. F3 using WinISD is about 38 Hz. I'm using the older analog RS sound level meter. The first...
  12. New user with a few questions about measurements

    REW Forum
    First let me say that REW is fantastic. Since I discovered it last weekend I can't stop using it! I have a DIY sub with a 12" Dayton driver and a 300 watt amp in a 2 cubic foot sealed enclosure. F3 using WinISD is about 38 Hz. I'm using the older analog RS sound level meter. The first...
  13. Another new rew user

    REW Forum
    I am a first time REW user and experimented with 2 subs. The best graph I got was with one sub, but if I am interpreting this graph correctly, I need a better sub. I used turtle bay sound card/xenyx802/8000mic. I got this graph earlier, but all other graphs had very poor lower ends...
  14. New user needing a checkup!

    REW Forum
    New user needing a checkup-reposted! Hello everyone, i'm new to this software so after 2 nights of messing about i think i have set it up ok and i have some graphs to show- i'm asking if everything looks ok and what "iyho" is the best crossover point for my sub in relation to the mains before...
  15. first time user

    REW Forum
    Here is what I got after hooking everything up and running the software. Can someone tell me if this looks correct? I want to buy a BFD if I am using this software correctly. See the graph below please.
  16. first time user and not a wizard....

    REW Forum
    HELP! I've installed the latest software and bought a Creative Sound Blaster X Fi sourround 5.1 external sound card. I'm using my RS Digital SPL and my laptop. I've been able to get through the sound card calibration and check levels on my main speakers. When I check the levels on the subs...
  17. NHT User

    New Member Introductions
    Hello all i am new to this forum i have a set of 2.3 (main) audiocenter and few SW2Si subs just wanted to say :hsd:i
  18. New user with graphs, I think they are wrong

    REW Forum
    Hey, here I'm showing a few graphs, I'm not sure if I am doing this right. The hardware list is the ECM8000 (with cal loaded) Xenex802 and the turtle beach external soundcard. *note: I did set the graphs to the "standard" setup but it does not cut the graph off, I guess all it does is zoom...
  19. Hello from a MAME user

    New Member Introductions
    I stumbled across this site in my search for a flat screen mounting rack that can rotate vertically for a future Home Theater / MAME rig that I plan on building to facilitate normal home theater and sidescrolling video game playing as well as vertical shooter video games by rotating the tv 90...
  20. Black Widow User!

    General Screen Discussion
    Has anyone heard of this?? Ive done some reading here and no i havent read every post yet but i did do a search and found nothing. I went into home depot cause they are the only ones that sell behr paint around here and i was looking for the bright whitle matte finish but they didnt have it. I...
Top