Search Results for ‘wrong’

Hi guys. Here is my first attempt at REW and i am just after some suggestions and help on how to make the best of my situation ? Here is my subwoofers only response. 100hz xover. 4 TC2+ 12" subs in an IB in the floor. Yamaha 3800 as pre pro into a Behringer Ultra Curve Pro. Here is my mains...

I dont understand why as I set my sweeps to start at a lower frequency the db's start high and lower. Should it start lower then go high. I finaly calibrated the sound card and my spl meter so Im not sure what the problem is. Sean

Folks, I've done a few sessions since finally figuring out how to make it all work, and setup had been smooth and easy. But yesterday, when I plugged everything in and made sure the .cal files were loaded, and USB Sound, Line-in, and Speaker chosen, all my soundcard levels were at 0.00. I...

Using a 2807 as pre with an ext SB card. Subs co-located in a(n) not too optimal location but the only available spot at this time. Mainly sitting in a 'null' located about 11' out from long side on the right wall in a 20'x40' room w/cathedral ceiling, open not sealed. Planning to use an...

When I vary the crossover settings from 40 to 120, it seems like I get pretty much the same respone curves. I have the mains disconnected and the sub on. Here are my responses. I have set the target settings (for each reading) to the target cut off that I am setting the crossover to. They...

Is the newecm.cal calibration curve really correct? All my measurements spike up from the 10k-20kHz range, exactly opposite to its compensation curve. At first I just thought it was that my tweeters needed some attenuation, but today while doing some measurements I did a full range sweep with...

Ok, I am using X-fi with Vista, 7.1 analog config with my receiver. Got X-fi calibrated, got cm-140 cal file loaded, have my cm-140 positioned. I go and click on the measure and then to start measure and sound is only coming from my center speaker.

Hi all I hope I can explain my question clearly, it would help if I was good at using paint or something, but I'll try a verbal description first. Room treatment, yes I'll get to it one day, but as I have to renovate the room yet, no point doing it fully just now. First reflection points, I...

First off this is my first attempt at an REW measurement and I have not had a lot of time to trouble shoot what's going on (I've already had a good couple hours into the set up). I think I have the sound card calibrated correctly. Why do things get so out of control at 200Hz and higher? Why...

I am using a M-Audio Revolution 5.1 soundcard with Windows Vista as my OS. When trying to calibrate the soundcard I can get to the point of having all my settings apparently correct but when I hit the next button to go to actual measurement the "Start Measuring" button is grayed out and nothing...

Consumers complain that repair costs are too high and that no one fixes anything any more. Servicers complain that they can't make a living because they can't get parts and support, and everything is built so cheap that it is not worth fixing. Manufacturers complain that there are not enough...

hi all, ive been reading about the bfd on this site for a while and even bought a dsp1124p almost a year ago. i finally got the time to hook it to a sub and after doing some measurements and sending the filters to the BFD, it didnt make any difference in the graphs. from all other indications...

Good evening all , spent most of the evening trying to calibrate using REW. I started by using the EZ EQ of the Harman Kardon AVR 635 then proceeded to REW to flatten the response if needed. I followed the instructions carefully everything seemed to be fine but when i took measurement wel...

I finally got around to trying REW again. Below are a couple graphs. The first is from the soundcard on my laptop being calibrated. The second is a room reading from 20hz to 100 hz. I had already done manual measurements and EQ corrections using the excel workbook for my RS meter so I'm...

I finally calibrated everything. I tried my first measure, and here is the graph I get ??? What is wrong ? Thank's for your time guys Chris