Home Theater Forum and Systems banner
xt32
1-19 of 25 Results
  1. Classifieds - Audio Equipment
    Near new condition, used for about a year. Still have original box and accessories.
  2. Audio Processing
    m redoing my whole setup and ended up with 2 avr's (Denon x4000 AND Pioneer SC25 + antimode 8033c). Budget is a big issue so I need to sell one setup or the other. This got me thinking about Dirac Live. Please let me know which option you think is best and any concerns I should be aware of...
  3. REW Forum
    Want to make sure I am doing this right, still learning and developing a process. 1) Run XT32 2) Connect the Umik-1 to my laptop and open REW (have narrow band 90 degree file with sensitivity number in the file)and the built in SPL meter 3) Fire up the blu-ray player and put in spears and...
  4. Audio Processing
    Will Audyssey XT32 + SubEQ HT provide the same corrections and work the same way if setting LFE/SUB to no and FR/FL mains to Large? I would like to take advantage of the subs in pure direct stereo mode and other by-pass options I am considering. This is for a secondary theater room I want to...
  5. Audio Processing
    Audyssey XT32 vs. Dirac Live Listening Comparison Introduction Last year HTS published a review of a the miniDSP DDRC-22D, a two-channel Dirac Live Digital Room Correction (DRC) product. The review included a comparison to Audyssey XT. A number of readers requested a comparison of Dirac Live...
  6. Home Theater System Recommendations
    I have landed on the Martin Logan Motion 40s for LR with a Motion 30 Center and FX for Surrounds. I spent about 2 hours yesterday listening to those speakers thru the Denon X5200W, Marantz SR7009, and the Yamaha RX-A3040 and to my ear the Yamaha sounded the most open and true to the demo audio...
  7. Electronic Processing/Equalization Devices
    Has anyone measured what these two would do to a sub? Are they complimentary, or redundant?
  8. Home Theater Receivers | Processors | Amps
    So I've got a dilemma I am hoping you can help me work through. I have an older Integra DTR 5.9 receiver. Its only got 4 HDMI inputs (HDMI 1.3). It also only has Audyssey 2EQ. I am driving a 5 channel set of Polk LSi speakers, which are 4 ohm and require dedicated amps, which I am using a...
  9. Home Theater Receivers | Processors | Amps
    I was kindly asked to ask this question on a separate thread and not the one I first posted it in! so here goes!! Hi guys!! What would be the best way to implement an anti-mode / 8033 cinema if you had either a receiver with multeq xt or multeq xt32 using two diy subs running through one...
  10. System Setup and Connection
    I have a Denon 4311 and using the Audyssey to set up all the speakers. Sometime when using the Audyssey the GUI will indicate that I need to raise or lower the volume of the subs. The GUI will have indicator that will change colors when the volume is around 75db (according to the GUI). After...
  11. DIY Subwoofers - General Discussion
    Finally going to jump into the DIY scene with a pair of Stereo Integrity 15s and the 3 cuft flat packs from DIY SG. I'm leaning toward the INuke 3000. Since my receiver uses Audyssey XT32 is there a need for bass boost or DSP functions on the amp? Room is sealed and even with the ported SVS...
  12. REW Forum
    I just got my new UMM-6 mic in the mail today and though I would take some measurements. My mains are large DIY 3-ways and my sub is also DIY, a 15" Dayton Quatro (no longer made) with 300W plate amp. Receiver is an Onkyo NR818. REW interface is UMM-6 with cal, with hdmi to the receiver and...
  13. Audio Processing
    re: Audyssey XT32 Hi all, I ran some graphs of my new drivers in old boxes today and was not very happy with how Audyssey XT32 has done my low tune. I have 3 tunes. 12.5hz, 17.5hz and 21.5hz. This was a sub I built a while ago but sold my old FI Q drivers and have now replaced with two Havoc...
  14. REW Forum
    Hi all, I ran some graphs of my new drivers in old boxes today and was not very happy with how Audyssey XT32 has done my low tune. I have 3 tunes. 12.5hz, 17.5hz and 21.5hz. This was a sub I built a while ago but sold my old FI Q drivers and have now replaced with two Havoc drivers. The...
  15. Electronic Processing/Equalization Devices
    Hey there, I'm one of the guys that are building our REW skills on AVS Forum - been a long time lurker here, and finally want to ask some questions about the EQ devices I'm considering to add to my HT setup, for use with REW's EQ feature that can export either auto or manually-generated filters...
  16. Home Theater Receivers | Processors | Amps
    Does anybody with a Onkyo 818 have any issues with it making the speakers WAY too bright after calibration? I ran it correctly, even tried different mics but all had the same results. This is my third receiver with Audyssey. Never had this issue before. I read the audyssey website up and down...
  17. System Setup and Connection
    I have 2 Polk Audio DSWmicropro 2000 subwoofers and a Denon 4311ci AVR. The subs have a mike, that is connected to sub, which is used for the "Autopro Room Resonance Correction" and the Denon uses the "Audyssey MultEQXT32" for speaker calibration. Which, or do I use both, do I use when...
  18. Home Theater Receivers | Processors | Amps
    Does anyone have a List of Receivers with Audyssey MultEQ XT32 ? or know a couple off the top of your head, link etc? Thanks!
  19. Home Audio Subwoofers
    I have dual PB13 Ultras and ran some REW tests that showed a big dip at the 70 hz crossover. I corrected the problem by making adjustments to the phase switch on both subs. My preamp is Onkyo 5508 and includes XT32. Should the dip be corrected by making physical phase adjustments on the subs...
1-19 of 25 Results
Top