Home Theater Forum and Systems banner

yamaha

  1. Home Theater System Recommendations
    so as i have a defective brand new rx-v 685 sold to me ,i plan to repair and sell it off.the reason i chose yamaha was the music and build per se.the trust in build part is completely shattered at least.so if i have to buy a new one viz., denon x2700h vs another 685.which one wud u suggest is...
  2. REW Forum
    Hi everyone, as a NPO we're experimenting multiamplification with an HT amplifier (Yamaha RX-V663) that provides a "measurement tool" for calibration (the well-known Ypao microphone). Even if we obviously know that it's not the best method to obtain good results, what level of accuracy do you...
  3. AV Home Theater
    Hi I need help with troubleshooting this Yamaha HTR5450 AV Receiver. When press Power ON, it shuts off within a sec. I downloaded the manual, and refering to the manual I entered the self diagnosis mode. In this mode, it shows "PS PRT 060" . Upon opening up the amp, the +5V and +12V regulators...
  4. Home Theater Receivers | Processors | Amps
    Looking at a new Yammy, the 5200. Online reviews are stellar. What is your experience (for those who own one)?
  5. Two Channel Audio
    https://www.soundandvision.com/content/yamaha-targets-audiophiles-upscale-hi-fi-series
  6. Home Theater Receivers | Processors | Amps
    Hi, I just introduced myself with my first two posts in the presentation thread. Excuse me for my English as a translator. I need to ask you: my Yamaha rx-A730 starts up well, but it takes 15 minutes for the icons of the speakers to appear on the display and for the speakers to be heard, it has...
  7. System Setup and Connection
    Hi all, have a question for you all. I have the above receiver, sub is a CSS SDX-15 powered by a Dayton Audio SA1000 amp. Amp is connected to pre out for sub. I ran the YPAO setup, it finds the sub, and I hear it during the setup. Problem is, there is no output from the sub otherwise. I have...
  8. Home Theater Receivers | Processors | Amps
    Hello, Helping my friend with this setup replacing V995 setup with crossover to AS710. I'm not experienced with a crossover so need some help here... When I connected speaker system as it was wired on V995 the 2 rear speakers are not working. I will run YPAO tomorrow but I'm not sure if I...
  9. Home Theater System Recommendations
    I currently have a 2.1 system with Pardigm Monitor 7's and PDR-10 sub powered by a Yamaha 797 channel receiver. I am looking to do a small theater by adding CC-290 center channel to this system and I am currently looking at the Yamaha RX-A810 receiver to power this. I can either run 3.1 or...
  10. General Service and Technical Information
    After years of solid service my Yamaha RX-V496 is starting to have a odd issue. :hissyfit: When the unit is turned on the left channel wont turn on until I turn the volume way up. :eek: once the left channel pops on I can turn the volume back down and the unit works normally. Any ideas on...
  11. Blu-ray | DVD | Disc Media Players
    I'm currently looking at a number of Universal Blu-Ray players. (i.e. Cambridge, Denon, Marantz, Yamaha & Oppo) I've done some research to find out what Audio DACs they all use. Only one I haven't been able to track down is the Yamaha. Has anyone taken the cover off a BD-A1010, or have some...
  12. System Setup and Connection
    Hey everyone, I am a little confused about the best way to hook up a Dayton Audio Sub-80 to my Yamaha HTR-6130 receiver. The sub does have its own amp and has its own power cord. The only low level inputs and outputs are via rca jacks, where as the high level is through speaker wire connection...
  13. Home Theater Receivers | Processors | Amps
    I was reading through the gain structure article in this forum and noticed a reference to my very own DEQ - the Yamaha DEQ7 (picked it up for $30 at a Music Go Round). Now, it was mentioned but not really explained what my optimal gain structure should be for an older piece of equipment like...
  14. Subwoofer Amps | High Pass Filters
    So I've got it narrowed down to these two amps for my L/C/R and sub duty. I'll be needing three of either of these amps total for my L/C/R and subs. I'll be powering 3 danley SM60F for L/C/R (rated 800w continuous / 1600w peak), leaving me three channels for sub duty. I'll be running 6...
  15. Home Theater Receivers | Processors | Amps
    I own a Aventage 700 as well as an Integra 20.3. I like the fact that the Yamaha can be used as a preamp, but the Integra automatically selects the sound source, (DOLBY D, DTS, whatever it is), while the Yamaha does not seem to be able to automatically select the sound, or is there a program...
  16. REW Forum
    I managed to get hold of a B&K 2270 for the weekend and have been seeing which of my budget microphones gives the most similar frequency response. Here's what I got: - The audio interface was an RME Multiface. My other microphones were all over the place, but the built in microphone on the...
  17. Home Theater Receivers | Processors | Amps
    Hello all, ive been browsing the site for a while but recently decided to sing up on forums here. Ive begun building my home theater in the past few weeks and im in the process of buying audio equipment. Im looking for a 5.1 AV Receiver at or under $400. Im looking for the money spent on the...
  18. Home Theater Receivers | Processors | Amps
    Hello, Sorry for pointing this out so late, but with this Promo Code EMCYTZT776, you can get a Brand New A3000 for simply an amazing price. Here is a Link to the AVR: http://www.newegg.com/Product/Product.aspx?Item=N82E16882115277 The Code gives you an additional $650 Dollars off and the A3000...
  19. System Setup and Connection
    Hi, I have a yamaha YHT-294 home theatre and i have the option of trading my speakers for the speakers on a samsung HT-D5550W system. My speakers are 6ohm and the samsungs are 3ohm, from what i have read if i run the amp hard i can damage it due to the 3ohm speakers, i dont usually go any...
  20. Home Theater Receivers | Processors | Amps
    So I have a Yamaha RX-V665 ... recently I have this annoying problem with it... I basically use 2 sources on HDMI inputs... a Cable Box and a PC.... Randomly the sound will quit working and I can cycle through each input and I get no sound. Only if I UNPLUG the rcvr and plug it back in then...
Top