Home Theater Forum and Systems banner

1 - 15 of 15 Posts

·
Registered
Joined
·
13 Posts
Discussion Starter #1
Hi everyone.
I have a Focusrite Saffire and I can not make a sound card calibration.
Line out 1-2 to line in 1-2.
Maybe there's a problem with windows mixer, I open it and only see 3 items for reproduction and none for record, it seems like the signal don't go thru saffire.
Thanks. Sorry for my english.
 

·
Registered
Joined
·
13 Posts
Discussion Starter #3
Hi. I have wdm and asio installed but, can I choose which one on windows?
Thanks brucek.
 

·
Registered
Joined
·
7,514 Posts
You can certainly choose which driver you want to install, but REW only works with WDM drivers installed.

brucek
 

·
Registered
Joined
·
13 Posts
Discussion Starter #5
On sound card windows properties I see wdm.
I can not choose what driver to install, its an exe.
Thanks
 

·
Registered
Joined
·
7,514 Posts
On sound card windows properties I see wdm
Good.

Maybe there's a problem with windows mixer, I open it and only see 3 items for reproduction and none for record, it seems like the signal don't go thru saffire
There's a Playback and a Record Mixer that must be selected independently.

When you select the speaker icon in the system tray you get the following select box.

Pull down Options and select Properties.

Windows Mixer select.jpg

Then select Playback and the items you want shown.

Select Playback or Record.jpg

Be sure line-in is muted in Playback as shown.

Playback.jpg

Then select Record and the items you want selected.

Select Playback or Record 2.jpg

Be sure line-in is selected

Record Mixer.jpg

So, does your system look anything like I've shown above?

brucek
 

·
Registered
Joined
·
13 Posts
Discussion Starter #7
No. I know all that settings but in this case, with saffire, I see only 3 items to choose, master-wave-sw synth and nothing else on playback.
And there's no items on record.
i assume that I need to reinstall something in windows.
Thanks.
 

·
Registered
Joined
·
7,514 Posts
i assume that I need to reinstall something in windows
Perhaps not. The Saffire card may have taken over those functions and are controllable now through the Saffire application software.

Do you have controls for Recording line-in with the application? If so, you should be able to get control of the line-in levels.

brucek
 

·
Registered
Joined
·
13 Posts
Discussion Starter #9
Yes, I have control with the saffire mixer and i use everyday without problems. But It seems that REW don't make any sound (I see VU movements on REW but I can't hear anything) Settings shows saffire for output and input.)
Thanks again.
 

·
Registered
Joined
·
7,514 Posts
Settings shows saffire for output and input.)
So, REW shows on the Settings page, the saffire in the Output Device and Input Device.

What does it show under that selection other then Default Output and Default Input. Does it show Speaker and Line-in?

Can you show a picture like the one below (as an example).

Another question: Are you able to produce any sound from your speakers with REW?

Settings.jpg

brucek
 

·
Registered
Joined
·
13 Posts
Discussion Starter #12
Sorry. Now its working.
Mixer.JPG

I realize that silence have a tild. Now I'm gonna to check everything else.
It seems that line in its working too.
Sorry again for your time.
Thanks.
 

·
Registered
Joined
·
13 Posts
Discussion Starter #14
Hi Brucek
I can not find the way to make a config file list for convolver. I have two impulses: 48000 and 44100 for windows media player. I can make a config file for one or another.
Thanks.
 

·
Registered
Joined
·
7,514 Posts
Sorry, I know very little about convolvers.

In the File menu, REW can Export the Impulse Response in a WAV format, and also the Filters IR as WAV.

brucek
 
1 - 15 of 15 Posts
Top